SJ5608 3M, SJ5608 Datasheet - Page 2

• Manufacturer Part Number: SJ5608
• Description: BUMPON ROLL 3.2MM 9"X36YD CLEAR
• Manufacturer: 3M
• Series: SJ-5600r

Specifications of SJ5608

• Shape: Rectangular, Flat - Customizable
• Color: Transparent - Clear
• Size: Roll - 108' L x 9.000" W x 0.125" H (32.92m x 228.60mm x 3.18mm) 1/8" H
• Size - Visible: Roll - 108' L x 9.000" W x 0.125" H (32.92m x 228.60mm x 3.18mm) 1/8" H
• Mounting Type: Adhesive - Acrylic
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 00-021200-26592-1; 70-0707-0779-2

Typical Adhesive
Performance
Characteristics
3M
Clear Polyurethane Rollstock
SJ-5632 • SJ-5616 • SJ-5608
Typical Physical
Properties and
Performance
Characteristics
™
Bumpon
™
Protective Products
Property
Hardness, Shore A
Approximate Density, lb./ft.
Resilience, %
Kinetic Coefficient of Friction*
Abrasion Resistance, gm/1000 cycles
Tensile, lb./in.
Elongation, %
Stain Resistance
Solvent Resistance
*Two important laws of friction applicable to 3M™ Bumpon™ Rollstock Protective Products are
Load Tolerance:
Application Temperature:
Service Temperature:
Note: The following technical information and data should be considered representative
Note: The following technical information and data should be considered representative
Static Shear Adhesive Performance
One in. overlap shear test; ASTM-D-3654-M (1000 gram); testing completed on stainless steel
test panels using 3M™ Bumpon™ Protective Product SJ-5616.
90° Peel Adhesion Performance
3M Test Method TM-2011; 72 hour dwell, 1/2 in. wide samples pulled at 12 in. per minute.
Testing completed using Bumpon protective product SJ-5616.
(1) friction is independent of the area of contact between solids and (2) friction is proportional to
the load between solids surfaces. Thus, if the load (weight) is doubled the force required to
cause surface sliding is also doubled. This is expressed mathematically as follows:
or typical only and should not be used for specification purposes.
or typical only and should not be used for specification purposes.
Polypropylene
Polystyrene
ABS
Stainless Steel
Aluminum
Glass
2
120°F (49°C)
158°F (70°C)
180°F (82°C)
Temperature
75°F (24°C)
(kPa)
Tested at:
Substrate
Slide force = (kinetic coefficient of friction) x (weight)
2
(gm/cm
The “recommended” maximum load which 3M™ Bumpon™
Protective Product 5600 series rollstock will support is 100 psi
(690 kPa) at 70°F (21°C) to 120°F (49°C).
40°F (4°C) to 125°F (52°C)
-30°F (-34°C) to 150°F (66°C); 225°F (107°C) intermittent exposure
- 2 -
3
)
Test Method
ASTM-D-2240
ASTM-D-2632
ASTM-D-1894
ASTM-C-501; Tabor H, 1 kg
ASTM-D-412, Die A
ASTM-D-412, Die A
3M - 24 hrs. at 158°F against white
paint, 7 days, 7 days exposed to UV
3M - 24 hr. immersion
Glass, Stainless Steel
Formica
5% Detergent in water
25% Detergent in water
5% Bleach in water
Gasoline
Motor Oil
Isopropyl Alcohol
®
Peel Force, oz. per 1/2 in.
Time to Failure, minutes
> 10,000
> 10,000
> 10,000
> 10,000
11
25
25
25
25
3
No apparent effect
No apparent effect
No apparent effect
No apparent effect
Slight swelling
Slight swelling
Test Results
No staining
740 (5100)
70 (1.1)
0.13
> 1
> 1
70
65
6