LC4H-R4-AC240VS Panasonic Electric Works, LC4H-R4-AC240VS Datasheet - Page 37
![COUNTER DIGITAL 240VAC SCREW](/photos/6/44/64491/lc4h-r4-ac240vs_sml.jpg)
LC4H-R4-AC240VS
Manufacturer Part Number
LC4H-R4-AC240VS
Description
COUNTER DIGITAL 240VAC SCREW
Manufacturer
Panasonic Electric Works
Series
LC4Hr
Datasheet
1.LC4H-R4-DC24V.pdf
(45 pages)
Specifications of LC4H-R4-AC240VS
Count Rate
30Hz or 5kHz Selectable
Number Of Digits/alpha
4
Input Type
Switch Closure or Transistor Switch
Output Type
Switch Closure
Voltage - Supply
100 V ~ 240 V
Display Type
LCD Red/Yellow
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
255-1219
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LC4H-R4-AC240VS
Manufacturer:
Panasonic Electric Works
Quantity:
135
INSTALLING DIN SIZE COUNTER
Installation methods
1. Surface mount
1) For the counters of LC4H series, use
the pin type counter.
2) Put the terminal socket on the board
directly or put it on the DIN rail (Fig. 1).
3) Insert the counter into the terminal
socket and fix it with clip (Fig. 2)
4) On DIN rail mounting, mount the
counter on the DIN rail tightly to get the
proper dimension (Fig. 3).
5) 8-pin type should be connected with
terminal socket AT8-DF8K. 11-pin type
should be connected with terminal sock-
et AT8-DF11K.
6) DIN rail (AT8-DLA1) is also available
(1 m).
2. Flush mount
1) For the counters of LC4H series, it is
recommended to use the built-in screw
terminal type for flush mount. (Mounting
frame and rubber gasket are provided
when counter is shipped.)
Terminal socket
DIN rail
(Fig. 3)
(Fig. 1)
(Fig. 2)
2) How to mount the counter
From the panel front, pass the counter
through the square hole. Fit the mount-
ing frame from the rear, and then push it
in so that the clearance between the
mounting frame and the panel surface is
minimized. In addition, lock the mount-
ing frame with a screw.
• LC4H series
3) Caution in mounting the counter
• LC4H series
waterproof types (IEC IP66), tighten the
reinforcing screws on the mounting
frames so that the counters, the rubber
gaskets, and the panel surfaces are
tightly contacted with each other.
(Tighten the two screws with uniform
force and make sure that there is no rat-
tling. If the screws are tightened too
excessively, the mounting frame may
come off.)
panel cover and the rubber gasket
removed, the waterproofing characteris-
tic is lost.
4) Removal
Loosen the screws on the mounting
frame, spread the edge of frame and
remove it.
Pull the mounting
frame backward
while spreading out
its hooks with your
thumbs and index
fingers.
a If the LC4H series are used as the
b If the counter is installed with the
Rubber
gasket
Panel cover
Mounting flame
Screw
PUSH
1
1
2
5) Correctly connect the terminals while
seeing the terminal layout and wiring
diagram.
6) If the pin type is used, the rear pin-
bracket (AT8-RR) or the 8P cap (AD8-
RC) is necessary to connect the pins.
For the 11-pin type, use the 11P cap
(AT8-DP11) and avoid directly soldering
the round pins on the counter.
7) Panel cutout dimensions
8) Although the
counters can be
mounted adja-
cent to each
other in this
case, it is rec-
ommended to
arrange the
mounting holes
as shown in the
figure to facili-
tate attaching
and detaching
the mounting
frame.
9) Adjacent mounting
Although the counters can be mounted
adjacent to each other, remember that
the panel surface of LC4H series counter
will lose its water-resistant effect. (Panel
thickness: 1 to 5 mm
A = (48 × n – 2.5)
When lining up the counters horizontally,
set the frames in such a position so the
formed spring areas are at the top and
bottom.
When lining up
the counters
vertically, set
the frames in
such a position
as the formed
spring areas
are at the right
and left.
1.772
45
+0.6
+.024
0
0
1.772
45
+0.6
0
+.024
0
Formed spring
Min. 80
Formed spring
3.150
+0.6
+0
The standard panel
cutout dimensions are
shown in the left fig-
ure. (Panel thickness:
1 to 5 mm
inch)
1.772
1.772
45
45
.039 to .197
+0.6
+0.6
0
0
+.024
+.024
0
0
1.772
45
+0.6
0
+.024
.039 to .197
0
Min. 80
3.150
A
inch)
145