PAXLC600 Red Lion Controls, PAXLC600 Datasheet - Page 6
![COUNTER 6-DIGIT BI-DIR COUNT](/photos/6/45/64521/paxlc600_sml.jpg)
PAXLC600
Manufacturer Part Number
PAXLC600
Description
COUNTER 6-DIGIT BI-DIR COUNT
Manufacturer
Red Lion Controls
Series
PAX®LITEr
Type
Counterr
Specifications of PAXLC600
Count Rate
25kHz
Number Of Digits/alpha
6
Input Type
Voltage
Voltage - Supply
10 V ~ 16 VDC,115 VAC, 230 VAC
Display Type
LED Red
No. Of Digits / Alpha
6
Digit Height
14.2mm
Power Consumption
6VA
Operating Temperature Range
0°C To +60°C
Signal Input Type
Pulse
Character Size
0.56"
Ip/nema Rating
IP65 / NEMA 4X
Connection Type
Cage-Clamp
Cut Out, Panel
3.62×1.77 "
Dimensions
4.2"L×3.8"W×1.95"H
Display Digit Height
0.56 "
Function
Counter
Number Of Digits
6
Primary Type
Electronic
Range, Measurement
-99999 to 999999
Special Features
Programmable
Termination
Terminal Block
Voltage, Supply
115/230 VAC, 10 to 16 VDC
Counter Supply Voltage
115/230VAC/10-16VDC
Display Font Color
Red
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Lead Free Status / Rohs Status
RoHS Compliant part
Other names
RLC101
operation or event. The pulses from a sensor are received by the PAXLC, and
then totalized on the display. In many cases the incoming pulses do not represent
the desired display readout. For those applications, a scale factor can be entered
into the meter, scaling the pulses to obtain the desired readout. The following
formula will help provide the scaling values to achieve the desired readout.
WHERE:
4.0 R
5.0 S
In many industrial applications, a meter is required to totalize the output of an
SF = DR
appropriate decimal point. When calculating the Scale Factor, use the whole
value of the number to be displayed, for example, 1.0 feet, the Desired
Readout in this case is 10. Do not use decimal points in the Scaling Formula.
For calculated SF values less than 9.99999
into the meter as the Scale Factor and the Scale Multiplier can be left at 1.
For calculated SF values greater than 9.99999
Multiplier must be used to reduce the calculated SF value until it is less then
9.99999. The Scale Multiplier multiplies the calculated Scale Factor value by
1, 0.1, and 0.01, thus reducing the calculated value accordingly. Select the
appropriate Scale Multiplier value that allows the Scale Factor to be a value
under 9.99999. Both the Scale Factor and Scale Multiplier can then be
entered into the meter.
SF = Scale Factor
DR = Desired Readout* (Single unit of measure, i.e. foot, gallon, etc.)
EPU = Existing Pulses per Unit (Number of pulses per single unit of
measure,
*For applications requiring a decimal point, select and program the
If the Scale Factor is a value less than 9.99999, it can be entered directly
If the Scale Factor is a value over 9.99999 (maximum value), the Scale
EPU
CALING THE
EVIEWING THE
i.e. foot, gallons, etc.)
PAR
KEY
DISPLAY MODE OPERATION
Access Programming Mode
No Function
Front Panel Reset
M
8. 8 . 8 . 8 . 8 . 8
ETER
F
RONT
PAR
PROGRAMMING MODE OPERATION
Store selected parameter and index to next parameter
Increment selected digit of parameter value
Select digit position in parameter value
6
Example 1:
provides a pulse for every can produced. The desired readout is in cases,
therefore the incoming pulses need to be converted to obtain the proper readout.
The following is used to calculate scale factor.
This application involves counting cases from a production line. The sensor
SF = DR
DR = 1 case
EPU = 12 cans/case
SF = 1
SF = 0.083333
entered directly into the meter. The Scale Multiplier can be left at 1.
B
Since the Calculated Scale Factor Value is less than 9.99999, it can be
EPU
12
UTTONS AND
D
ISPLAY