LD2006P0 Red Lion Controls, LD2006P0 Datasheet - Page 12
![COUNTER 6 DIGIT DUAL 2.25" RED](/photos/6/45/64523/mfg_ld_series_sml.jpg)
LD2006P0
Manufacturer Part Number
LD2006P0
Description
COUNTER 6 DIGIT DUAL 2.25" RED
Manufacturer
Red Lion Controls
Series
LDr
Type
Counterr
Specifications of LD2006P0
Count Rate
35kHz
Number Of Digits/alpha
6
Input Type
Voltage, Switch Closure, Transistor Switch
Output Type
Relay and RS232/RS485
Voltage - Supply
11 V ~ 16 VDC, 85 V ~ 250 VAC
Display Type
LED Red
No. Of Digits / Alpha
6
Digit Height
57mm
Power Consumption
26VA
Counting Speed
25kHz
Operating Temperature Range
0°C To +50°C
Signal Input Type
Pulse
Ip/nema Rating
IP65 / NEMA 4X
Accuracy
±0.01% %
Connection Type
Wire Leads
Dimensions
16"L×2.25"W×4"H
Display Digit Height
2.25 "
Function
Counter
Material, Casing
Aluminum
Number Of Digits
6
Primary Type
Electronic
Range, Measurement
0 to 99999
Special Features
RS485/RS232 Communications
Termination
Terminal Block
Voltage, Supply
85 to 250/11 to 16 VAC/VDC
Counter Supply Voltage
85-250VAC/11-16VDC
Display Font Color
Red
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
is “on”. Reverse (
chart below. Boundary mode is not applicable for Counter B assignment.
mode (
the Setpoint Value is reached.
increment digit 6 to display a “-” sign (Counter A only).
deactivated. Reverse (
when deactivated.
powered down.
output at power up.
SPT ACTION DESCRIPTION
Normal (
This parameter selects the action of the Setpoint output as described in the
Select the display the Setpoint is to be assigned.
This parameter is only active if the Setpoint Action is set to timed output
Normal (
Enter the desired Setpoint value. To enter a negative setpoint value,
will restore the output to the same state it was at before the meter was
Latched Output Mode
Timed Output Mode
Boundary Mode
(High Acting)
Boundary Mode
(Low Acting)
SETPOINT OUTPUT POWER-UP STATE
). Enter the value in seconds that the output will be active, once
) displays the setpoint annunciator when the corresponding output
) turns the output “on” when activated and “off” when
SETPOINT OUTPUT TIME-OUT
will activate the output at power up.
SETPOINT OUTPUT ACTION
) displays the setpoint annunciator when the output is “off”.
SETPOINT OUTPUT LOGIC
SETPOINT ANNUNCIATOR
SETPOINT ASSIGNMENT
) turns the output “off” when activated and “on”
SETPOINT VALUE
Count A:
Count B:
Rate:
to
OUTPUT ACTIVATES
When Count =
When Count =
When Count
When Count
Setpoint
Setpoint
Setpoint
Setpoint
to
to
seconds
to
OUTPUT DEACTIVATES
At Manual Reset
Output Time-Out
(if
will deactivate the
After Setpoint
When Count
When Count
< Setpoint
> Setpoint
=
)
12
value (
output when the assigned display value is less than or equal to the Setpoint.
value crosses into the output “off” area. Once in the output “off” area, the
Setpoint will then function per the description for Low Acting Boundary Type.
each time the Setpoint value is reached. The automatic reset can occur at output
start, or output end if the Setpoint Output Action is programmed for timed
output mode. The Reset-to-Count Load selections (“
Counter A assignment. This reset may be different from the Counter A Reset
Action selected in Module 1.
Setpoint 2 output (O1 off at O2). The “
Output Action is programmed for timed output.
Setpoint 1 output (O2 off at O1). The “
Output Action is programmed for timed output.
Setpoint Assigned Counter is reset. The counter reset can occur by the
key, User Input or Counter Reset at Power-up.
Setpoint generated Counter Auto Reset.
SELECTION
High Acting Boundary Type activates the output when the assigned display
This parameter only applies to Low Acting Boundary Type setpoints. Select
This parameter automatically resets the Setpoint Assigned Counter (A or B)
SETPOINT 1 OUTPUT OFF AT SETPOINT 2 (SP1 Only)
This parameter will deactivate Setpoint 1 output at the Start or End of
SETPOINT 2 OUTPUT OFF AT SETPOINT 1 (SP2 Only)
This parameter will deactivate Setpoint 2 output at the Start or End of
Selecting
This output reset will not occur when the Assigned Counter is reset by a
to disable a Low Acting Setpoint at power-up, until the assigned display
SETPOINT OUTPUT RESET WITH MANUAL RESET
ACTION
No Auto Reset
Reset to Zero at the Start of output activation
Reset to Count Load value at the Start of output activation
Reset to Zero at the End of output activation (timed out only)
Reset to Count Load at the End of output activation (timed out only)
) equals or exceeds the Setpoint value. Low Acting activates the
SETPOINT STANDBY OPERATION
causes the Setpoint output to deactivate (reset) when the
SETPOINT BOUNDARY TYPE
COUNTER AUTO RESET
” setting only applies if Setpoint 2
” setting only applies if Setpoint 1
”) only apply to
RST