LD400400 Red Lion Controls, LD400400 Datasheet - Page 15
![COUNTER 4 DIGIT 4.0" 120VAC RED](/photos/6/45/64523/mfg_ld_series_sml.jpg)
LD400400
Manufacturer Part Number
LD400400
Description
COUNTER 4 DIGIT 4.0" 120VAC RED
Manufacturer
Red Lion Controls
Series
LDr
Type
Counterr
Specifications of LD400400
Count Rate
35kHz
Number Of Digits/alpha
4
Input Type
Voltage
Voltage - Supply
11 V ~ 16 VDC, 85 V ~ 250 VAC
Display Type
LED Red
No. Of Digits / Alpha
4
Digit Height
101mm
Power Consumption
26VA
Counting Speed
25kHz
Operating Temperature Range
0°C To +50°C
Signal Input Type
Pulse
Character Size
4"
Ip/nema Rating
IP65 / NEMA 4X
Connection Type
Wire Leads
Dimensions
20"L×2.25"W×7.875"H
Display Digit Height
4 "
Function
Counter
Material, Casing
Aluminum
Number Of Digits
6
Primary Type
Electronic
Special Features
RS485/RS232 Communications
Termination
Terminal Block
Voltage, Supply
85 to 250/11 to 16 VAC/VDC
Counter Supply Voltage
85-250VAC/11-16VDC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Lead Free Status / Rohs Status
RoHS Compliant part
Other names
RLC118
Abbreviated Transmission
* These characters only appear in the last line of a block print.
leaving only the numeric part of the response.
Command Response Time
operation). During RS232 transmissions, the meter ignores commands while
transmitting data, but instead uses RXD as a busy signal. When sending
commands and data to the meter, a delay must be imposed before sending
another command. This allows enough time for the meter to process the
command and prepare for the next command.
string to the com port, thus initiating a transmission. During t
characters are under transmission and at the end of this period, the command
terminating character (* or $) is received by the meter. The time duration of t
is dependent on the number of characters and baud rate of the channel.
command and when complete, performs the command function. This time
interval t
to accept another command.
of the command terminating character. The ‘*’ terminating character results in
a response time of 50 msec. minimum. This allows sufficient time for the
release of the sending driver on the RS485 bus. Terminating the command line
with ‘$’ results in a response time (t
time of this terminating character requires that sending drivers release within 2
msec. after the terminating character is received.
Communication Format
In serial communications, the voltage is switched between a high and low level
at a predetermined rate (baud rate) using ASCII encoding. The receiving device
reads the voltage levels at the same intervals and then translates the switched
levels back to a character. The voltage level conventions depend on the interface
standard. The table lists the voltage levels for each standard.
characters (0 to
an optional parity bit and one or more ending stop bits. The data format and
baud rate must match that of other equipment in order for communication to
take place. The figures list the data formats employed by the meter.
Byte
1-12
The abbreviated response suppresses the node address and register ID,
The meter can only receive data or transmit data at any one time (half-duplex
At the start of the time interval t
At the start of time interval t
If the meter is to reply with data, the time interval t
Data is transferred from the meter through a serial communication channel.
Data is transmitted one byte at a time with a variable idle period between
13
14
15
16
17
* Voltage levels at the Receiver
LOGIC
1
0
2
Description
12 byte data field, 10 bytes for number, one byte for sign,
one byte for decimal point
<CR> (carriage return)
<LF> (line feed)
<SP>* (Space)
<CR>* (carriage return)
<LF>* (line feed)
varies. If no response from the meter is expected, the meter is ready
t
1
INTERFACE STATE
= (10 times the # of characters) / baud rate
space (active)
). Each ASCII character is “framed” with a beginning start bit,
mark (idle)
Character Frame Figure
2
, the meter starts the interpretation of the
1
2
TXD,RXD; +3 to +15 V
, the computer program prints or writes the
TXD,RXD; -3 to -15 V
) of 2 msec. minimum. The faster response
RS232*
2
is controlled by the use
a-b > +200 mV
a-b < -200 mV
1
, the command
RS485*
1
15
Meter Response Examples:
1. Node address = 17, full field response, Counter A = 875
2. Node address = 0, full field response, Setpoint 1 = -250.5
3. Node address = 0, abbreviated response, Setpoint 1 = 250, last line of block
character of the reply. As with t
number of characters and baud rate of the channel. At the end of t
ready to receive the next command.
times t
Start Bit and Data Bits
receiving device to prepare for reception of data. One bit period later, the least
significant bit of the ASCII encoded character is transmitted, followed by the
remaining data bits. The receiving device then reads each bit position as they are
transmitted.
Parity Bit
a zero or a one, so that the total number of ones contained in the transmission
(including the parity bit) is either even or odd. This bit is used by the receiver
to detect errors that may occur to an odd number of bits in the transmission.
However, a single parity bit cannot detect errors that may occur to an even
number of bits. Given this limitation, the parity bit is often ignored by the
receiving device. The meter ignores the parity bit of incoming data and sets the
parity bit to odd, even or none (mark parity) for outgoing data.
Stop Bit
period pause to allow the receiver to prepare to re-synchronize to the start of a
new transmission (start bit of next byte). The receiver then continuously looks
for the occurrence of the start bit. If 7 data bits and no parity is selected, then 2
stop bits are sent from the meter.
print
At the beginning of time interval t
The maximum serial throughput of the meter is limited to the sum of the
Data transmission always begins with the start bit. The start bit signals the
After the data bits, the parity bit is sent. The transmitter sets the parity bit to
The last character transmitted is the stop bit. The stop bit provides a single bit
RESPONSE FROM METER
NO REPLY FROM METER
1
Ready
Ready
, t
17 CTA
SP1
2
and t
t
3
= (10 times the # of characters) / baud rate
3
.
Terminator
Transmission
Command
Command
Received
String
-250.5<CR><LF>
250<CR><LF><SP><CR><LF>
875 <CR><LF>
t
t
1
1
Timing Diagram Figure
1
, the time duration of t
Character
Response
of Reply
Meter
Time
t
t
First
2
2
3
, the meter responds with the first
Ready
Transmission
Reply
Time
t
3
3
is dependent on the
Ready
3
, the meter is