LD4006P0 Red Lion Controls, LD4006P0 Datasheet - Page 3
![COUNTER 6 DIGIT DUAL 4.0" RED](/photos/6/45/64523/mfg_ld_series_sml.jpg)
LD4006P0
Manufacturer Part Number
LD4006P0
Description
COUNTER 6 DIGIT DUAL 4.0" RED
Manufacturer
Red Lion Controls
Series
LDr
Type
Counterr
Specifications of LD4006P0
Count Rate
35kHz
Number Of Digits/alpha
6
Input Type
Voltage, Switch Closure, Transistor Switch
Output Type
Relay and RS232/RS485
Voltage - Supply
11 V ~ 16 VDC, 85 V ~ 250 VAC
Display Type
LED Red
No. Of Digits / Alpha
6
Digit Height
101mm
Power Consumption
26VA
Counting Speed
25kHz
Operating Temperature Range
0°C To +50°C
Signal Input Type
Pulse
Character Size
4"
Ip/nema Rating
IP65 / NEMA 4X
Accuracy
±0.01% %
Connection Type
Wire Leads
Dimensions
26"L×2.25"W×7.875"H
Display Digit Height
4 "
Function
Counter
Material, Casing
Aluminum
Number Of Digits
6
Primary Type
Electronic
Range, Measurement
0 to 99999
Special Features
RS485/RS232 Communications
Termination
Terminal Block
Voltage, Supply
85 to 250/11 to 16 VAC/VDC
Counter Supply Voltage
85-250VAC/11-16VDC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
EMC INSTALLATION GUIDELINES
Magnetic Interference (EMI), proper installation and wiring methods must be
followed to ensure compatibility in each application. The type of the electrical
noise, source or coupling method into the meter may be different for various
installations. The meter becomes more immune to EMI with fewer I/O
connections. Cable length, routing, and shield termination are very important
and can mean the difference between a successful or troublesome installation.
Listed below are some EMC guidelines for successful installation in an
industrial environment.
1. The meter should be properly connected to protective earth.
2. Use shielded (screened) cables for all Signal and Control inputs. The shield
3. Never run Signal or Control cables in the same conduit or raceway with AC
SETTING THE 8 DIP SWITCHES
eight switches is located inside the unit.
SWITCH 1 (Input A)
SWITCH 2 (Input A) {See Note 1}
SWITCH 3 (Input A)
SWITCH 4 (Input B) {See Note 1}
SWITCH 5 (Input B)
2.0 S
3.0 W
Although this meter is designed with a high degree of immunity to Electro-
(screen) pigtail connection should be made as short as possible. The
connection point for the shield depends somewhat upon the application.
Listed below are the recommended methods of connecting the shield, in order
of their effectiveness.
a. Connect the shield only at the panel where the unit is mounted to earth
b. Connect the shield to earth ground at both ends of the cable, usually when
c. Connect the shield to common of the meter and leave the other end of the
power lines, conductors feeding motors, solenoids, SCR controls, and
heaters, etc. The cables should be ran in metal conduit that is properly
grounded. This is especially useful in applications where cable runs are long
and portable two-way radios are used in close proximity or if the installation
is near a commercial radio transmitter.
To access the switches, remove the right side plate of the meter. A bank of
LOGIC: Input A trigger levels V
MAG: 200 mV peak input sensitivity; 100 mV hysteresis; maximum voltage:
SNK.: Adds internal 7.8 K pull-up resistor to +12 VDC, I
SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.
HI Frequency: Removes damping capacitor and allows max. frequency.
LO Frequency: Adds a damping capacitor for switch contact bounce. Limits
SNK.: Adds internal 7.8 K pull-up resistor to +12 VDC, I
SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.
HI Frequency: Removes damping capacitor and allows max. frequency.
LO Frequency: Adds a damping capacitor for switch contact bounce. Limits
ground (protective earth).
the noise source frequency is above 1 MHz.
shield unconnected and insulated from earth ground.
V
40 V peak (28 Vrms); Must also have SRC switch ON. (Not recommended
with counting applications.)
input frequency to 50 Hz and input pulse widths to 10 msec.
input frequency to 50 Hz and input pulse widths to 10 msec.
MAX
Warning: Exposed line voltage exists on the circuit boards.
Remove all power to the meter and load circuits before accessing
inside of the meter.
= 28 VDC
ETTING THE
IRING THE
IL
= 1.25 V max.; V
M
DIP S
IH
MAX
MAX
= 2.75 V min.;
ETER
= 2.1 mA.
= 2.1 mA.
WITCHES
3
SWITCH 6 (RESET/USER INPUT) {See Note 1}
SWITCH 7 (POWER UP RESET)
Note: This switch has no function for programmable models. Power-up reset is
SWITCH 8 (Input B)
Note 1: When the DIP switch is in the SNK position (OFF), the input is
4. Signal or Control cables within an enclosure should be routed as far as possible
5. In extremely high EMI environments, the use of external EMI suppression
6. Long cable runs are more susceptible to EMI pickup than short cable runs.
7. Switching of inductive loads produces high EMI. Use of snubbers across
SNK.: Adds internal 7.8 K pull-up resistor to +12VDC, I
SRC.: Adds internal 3.9 K pull-down resistor, 7.2 mA max. @ 28 VDC max.
ENABLE: In this position, the counter resets to zero at power up.
DISABLE: In this position, the counter does not reset at power up.
selected through a programming parameter.
DIRECTION CONTROL: In this position Input B is used to control the
INTENSITY ADJUST: In this position Input B is used to adjust the
configured as active low. When the switch is in the SRC position (ON), the
input is configured as active high.
from contactors, control relays, transformers, and other noisy components.
devices, such as ferrite suppression cores, is effective. Install them on Signal
and Control cables as close to the unit as possible. Loop the cable through the
core several times or use multiple cores on each cable for additional protection.
Install line filters on the power input cable to the unit to suppress power line
interference. Install them near the power entry point of the enclosure. The
following EMI suppression devices (or equivalent) are recommended:
Note: Reference manufacturer's instructions when installing a line filter.
Therefore, keep cable runs as short as possible.
inductive loads suppresses EMI.
Snubber: RLC# SNUB0000.
count direction of Input A when Input A is set to Count with Direction
mode (default mode).
LED intensity. There are five distinct LED levels that can be changed by
pulsing Input B. After setting the desired intensity, move switch to
OFF position for Direction Control. Units with keypads can program the
LED intensity level using Programming Menu 3.
Ferrite Suppression Cores for signal and control cables:
Line Filters for input power cables:
Fair-Rite # 0443167251 (RLC# FCOR0000)
TDK # ZCAT3035-1330A
Steward # 28B2029-0A0
Schaffner # FN610-1/07 (RLC# LFIL0000)
Schaffner # FN670-1.8/07
Corcom # 1 VR3
Input B Direction Control
Pwr Up Reset DISABLE
Reset/User Input SNK.
Input A
Input B
HI FREQ.
HI FREQ.
LOGIC
SNK.
SNK.
5
6
8
1
2
3
4
7
Factory Setting
ON
MAG.
SRC.
LO FREQ.
SRC.
LO FREQ.
SRC.
ENABLE
Intensity Adjust
MAX
= 2.1 mA.