PAXI0000 Red Lion Controls, PAXI0000 Datasheet - Page 17
![1/8 DIN DIGITAL INPUT PANEL METE](/photos/21/40/214052/4244351_sml.jpg)
PAXI0000
Manufacturer Part Number
PAXI0000
Description
1/8 DIN DIGITAL INPUT PANEL METE
Manufacturer
Red Lion Controls
Series
PAXr
Type
Multimeterr
Specifications of PAXI0000
Display Style
Red Characters, Black Background
Display Type
LED
Display Face Size
3.80" L x 1.95" W (96.5 x 49.5mm)
Display Digits
6
Display Digits - Height
0.560" (14.22mm)
Mounting Type
Panel Mount
Termination
Terminal Block
Voltage - Supply
85 ~ 250VAC
No. Of Digits / Alpha
6
Signal Input Type
Pulse
Character Size
0.56"
Ip/nema Rating
IP65 / NEMA 4X
Panel Cutout Height
1.77"
Display Font Color
Red
Panel Cutout Width
3.62"
Accuracy
±0.01% %
Connection Type
Cage-Clamp
Cut Out, Panel
1/8 DIN
Digit Height
0.56
Dimensions
4.2"L×3.8"W×1.95"H
Display Digit Height
0.56 "
Function
Counter/Rate Indicator
Indicator Type
Counter/Rate Indicator
Number Of Digits
5
Primary Type
Electronic
Range, Measurement
±99999999
Special Features
Programmable Function Keys
Temperature, Operating, Range
0 to 50 °C
Voltage, Supply
85 to 250 VAC
Counter Supply Voltage
85-250VAC
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Backlight
-
Measuring Range
-
Lead Free Status / Rohs Status
RoHS Compliant part
Other names
Q4600348
Shaded areas are model dependent.
Program lock-out.
by repeatedly pressing the DSP key. An annunciator indicates the display being
shown. These displays can be locked from being visible. It is recommended that
the display be set to
modified. This Programming Mode can be locked with a security code and/or
user input. When locked and the PAR key is pressed, the meter enters a Quick
Programming Mode. In this mode, setpoint, count load and scale factor values
can still be read and/or changed per the selections below. The Display Intensity
Level (
enabled, and the security code is greater than zero.
6.3 MODULE 3 - D
These displays can be programmed for
Module 3 is the programming for Display lock-out and “Full” and “Quick”
When in the Display Mode, the available displays can be read consecutively
“Full” Programming Mode permits all parameters to be viewed and
SELECTION
x = Counter A , Counter B, and then Counter C
n = Setpoints 1 to 4
Throughout this document, Programming Mode (without Quick in front) always refers to “Full” Programming (all meter parameters are accessible).
SECURITY
SELECTION
CODE
>0
>0
>0
) parameter also appears whenever Quick Programming Mode is
COUNTER A B C DISPLAY LOCK-OUT *
0
0
0
MAX. MIN. DISPLAY LOCK-OUT *
DESCRIPTION
Visible but not changeable in Quick Programming Mode
Visible and changeable in Quick Programming Mode
Not visible in Quick Programming Mode
RATE DISPLAY LOCK-OUT *
CONFIGURED
USER INPUT
not
not
DESCRIPTION
Visible in Display Mode
Not visible in Display Mode
when the corresponding function is not used.
USER INPUT
Not Active
Not Active
————
————
STATE
Active
Active
or
Quick Programming w/Display Intensity
Quick Programming w/Display Intensity
ISPLAY AND
.
Quick Programming
“Full” Programming
“Full” Programming
“Full” Programming
PROGRAMMING MODE ACCESS
WHEN PAR KEY IS
PARAMETER MENU
PRESSED
P
ARAMETERS
17
P
ROGRAM
following table). Accessible only with the Setpoint Plug-in card installed.
COUNT LOAD A B C ACCESS LOCK-OUT *
SCALE FACTOR A B C ACCESS LOCK-OUT *
access the “Full” Programming Mode. Access will only be allowed after entering
a matching security code or universal code of
would not have to be configured for Program Lock-out. However, this lock-out is
overridden by an inactive user input configured for Program Lock-out.
*
The setpoint displays can be programmed for
Factory Setting can be used without affecting basic start-up.
These displays can be programmed for
The Scale Factor values can be programmed for
Entry of a non-zero value will cause the prompt
“FULL” PROGRAMMING MODE ACCESS
Immediate access.
After Quick Programming with correct code # at
After Quick Programming with correct code # at
Immediate access.
No access
Immediate access.
Shaded areas represent program access that is model dependent.
SETPOINT 1 to 4 ACCESS LOCK-OUT *
L
(
OCK
SECURITY CODE *
to
-
OUT
)
,
. With this lock-out, a user input
, or
,
to appear when trying to
,
prompt.
prompt.
, or
.
, or
.
(See the