DS26502LN+ Maxim Integrated Products, DS26502LN+ Datasheet - Page 21
DS26502LN+
Manufacturer Part Number
DS26502LN+
Description
IC T1/E1/J1 64KCC ELEMENT 64LQFP
Manufacturer
Maxim Integrated Products
Type
BITS Elementr
Datasheet
1.DS26502LN.pdf
(125 pages)
Specifications of DS26502LN+
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Frequency-max
-
Output
-
Input
-
- Current page: 21 of 125
- Download datasheet (4Mb)
4.5 JTAG
4.6 Line Interface
RRING
NAME
JTCLK
NAME
TRING
MCLK
JTRST
THZE
JTMS
JTDO
RTIP
JTDI
TTIP
TYPE
TYPE
O
O
O
I
I
I
I
I
I
I
I
JTAG Clock. This clock input is typically a low frequency (less than 10MHz)
50% duty cycle clock signal.
JTAG Mode Select (with Pullup). This input signal is used to control the
JTAG controller state machine and is sampled on the rising edge of JTCLK.
JTAG Data Input (with Pullup). This input signal is used to input data into
the register that is enabled by the JTAG controller state machine and is sampled
on the rising edge of JTCLK.
JTAG Data Output. This output signal is the output of an internal scan shift
register enabled by the JTAG controller state machine and is updated on the
falling edge of JTCLK. The pin is in the high-impedance mode when a register
is not selected or when the JTRST signal is high. The pin goes into and exits the
high impedance mode after the falling edge of JTCLK
JTAG Reset (Active Low). This input forces the JTAG controller logic into
the reset state and forces the JTDO pin into high impedance when low. This pin
should be low while power is applied and set high after the power is stable.
The pin can be driven high or low for normal operation, but must be high for
JTAG operation.
Master Clock Input. A (50ppm) clock source. This clock is used internally for
both clock/data recovery and for the jitter attenuator for both T1 and E1 modes.
The clock rate can be 16.384MHz, 8.192MHz, 4.096MHz, or 2.048MHz. When
using the DS26502 in T1-only operation, a 1.544MHz (50ppm) clock source
can be used.
Receive Tip. Analog input for clock recovery circuitry. This pin connects via a
1:1 transformer to the network. See the Line Interface Unit section for details.
Receive Ring. Analog input for clock recovery circuitry. This pin connects via
a 1:1 transformer to the network. See the Line Interface Unit section for details.
Transmit Tip. Analog line-driver output. This pin connects via a 1:2 step-up
transformer to the network. See the Line Interface Unit section for details.
Transmit Ring. Analog line-driver output. This pin connects via a 1:2 step-up
transformer to the network. See the Line Interface Unit section for details.
Transmit High-Impedance Enable. When high, TTIP and TRING will be
placed into a high-impedance state.
21 of 125
FUNCTION
FUNCTION
Related parts for DS26502LN+
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
T1/E1/J1/64KCC BITS Element
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
power light source LUXEON® Collimator
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products