U2102B-MFPG3Y Atmel, U2102B-MFPG3Y Datasheet
![IC TIMER CTRL IGBT/MOSFET 16SOIC](/photos/6/50/65034/453-16-sioc_sml.jpg)
U2102B-MFPG3Y
Specifications of U2102B-MFPG3Y
Related parts for U2102B-MFPG3Y
U2102B-MFPG3Y Summary of contents
Page 1
... Timers 1. Description The timer control circuit U2102B is based on bipolar technology. The output stage can switch either a MOSFET or an IGBT. Two sensor inputs and the retriggerable and adjustable tracking time useful for a wide range of applications. By using the reverse phase-control technique, the resistive load can be dimmed without the need of a com- pensation inductance ...
Page 2
... Figure 1-1. Block Diagram 1 V Ref 2 Reverse 3 phase control oscillator 6 Programing Triggering with buffers 7 8 U2102B 2 Voltage monitoring Control Divider logic 9 16 Synchronization Voltage limitation Push pull Current monitoring Temperature Test logic monitoring 4767B–INDCO–10/05 ...
Page 3
... Test output 11 II Input current monitoring 12 IOFF Fast output current monitoring 13 GND Ground 14 VO Output voltage 15 +VS Supply voltage 16 SYNC Synchronization input 4767B–INDCO–10/05 1 VREF 2 CRAMP RRAMP 3 4 CONTROL U2102B 5 OSC PROG TRIGGER 8 SYNC GND IOFF TEST 9 V9 U2102B 3 ...
Page 4
... Figure 2-2. Block Diagram with Typical Circuit for DC Loads U2102B 4 4767B–INDCO–10/05 ...
Page 5
... Power Supply, Synchronization Pins 15 and 16 The U2102B’s voltage limitation circuit enables the power supply via the dropping resistor R the case of DC loads, the entire supply current flows into pin 16 and is supplied via an internal diode to pin 15, where the resultant supply voltage is limited and smoothed by C resistor at pin 16 is necessary in order to guarantee reliable synchronization ...
Page 6
... A sufficiently large residual phase angle must remain in this case to guarantee the device’s supply. The power supply is simplified if the device is operated as a static zero-voltage switch for AC loads (see module is connected directly to the AC line. U2102B 6 V – V ...
Page 7
... Chip Temperature Monitoring The U2102B includes a chip temperature monitoring circuit which disables the output stage when a temperature of approximately 140°C is reached. The circuit will only be enabled again after cooling down and when the operating voltage has been additionally switched off and on. ...
Page 8
... Figure 6-1. Signal Characteristics of Reverse Phase Control V mains Ref Ref V 14 U2102B reduced 5.5 V. The charging current is switched off at this point and 7). at pin 2 is set with the resistor R 3 0.45 V. The output stage is switched on at this value = I . Since the actual zero crossing of the supply ...
Page 9
... set when the timer has enabled the output stage. max = The window discriminator is in the OFF state when the voltage at pin guarantees that there are no peak noise signals at the inputs ON U2102B = Ref = GND): 6 ...
Page 10
... An internal RC oscillator with following divider stage 1:2 tracking time. The RC values for a certain tracking time (µ reverse phase control mode, switchover from maximum current flow angle to the value set at pin 4 takes place after expiry of 3/4 of the total tracking time t U2102B 10 Trigger Condition Pin Ref 0.5 V Ref 0.1/0.4 ...
Page 11
... Current Monitoring The U2102B’s current monitoring circuit represents a double electronic fuse. The circuit mea- sures the current flowing through the power switch by means of the voltage drop across the shunt resistor R due to a high load current (e.g., short circuit), the switch-off latch is set and the switching output pin 11 closes immediately ...
Page 12
... Control Voltage Input voltage Input current V Programming, Tri-state Input Input current V Operating mode: Static zero-voltage switch 2-stage reverse phase control with switch-off 2-stage reverse phase control RC Oscillator Input current V Upper threshold Lower threshold Discharge impedance U2102B 12 Symbol R thJA R thJA R thJA Pin = ...
Page 13
... TU1 V 1.1 1.25 TL2 V 3.4 3.75 TU2 ±I 500 i V 2 0.45 0.5 0. 100 115 T ±I 500 100 120 T1 V 450 500 550 T2 I lkg V Sat V Sat -V Sat V SatL - U2102B Unit 1 2 µA 1.0 V 1.2 V 2 ...
Page 14
... Figure 13-1. House Number or Staircase Illumination for AC Loads House Number Illumination: V Staircase Illumination mains 230 V ~ Load R sync 220 k U2102B GND IGBT 100 R 1 1N4007 µF/ 100 U2102B 820 k Control 100 Ref NTC Ref GND Enable 220 Trigger signal 1 µF 4767B–INDCO–10/05 ...
Page 15
... Figure 13-2. Zero-voltage Switch Mode for AC Loads sync 1N4007 4767B–INDCO–10/05 V mains 230 V ~ Load GND R sh IGBT 100 µF/ U2102B 750 NTC V Ref Enable 2 220 nF Trigger signal C 1 µF Ref U2102B 15 ...
Page 16
... Figure 13-3. Reverse Phase Control for AC Loads V 230 220 k sync U2102B 16 mains Load IGBT 100 1N4007 100 k 47 µF/ 25V U2102B 100 Control 100 100 100 µF Ref 4767B–INDCO–10/05 ...
Page 17
... Package DIP16 SO16 SO16 20.0 max 1.64 0.58 2.54 1.44 0.48 17. Remarks Tube, Pb-free Tube, Pb-free Taped and reeled, Pb-free 7.82 7.42 4.8 max 6.4 max 3.3 0.5 min 0.39 max 9.75 8.15 technical drawings according to DIN specifications U2102B 17 ...
Page 18
... Package SO16 Dimensions 16. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4767B-INDCO-08/05 U2102B 18 10.0 9.85 0.4 1.27 8. History Put datasheet in a new template First page: Pb-free logo added Page 17: Ordering Information changed 5 ...
Page 19
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...