LMK03033CISQE/NOPB National Semiconductor, LMK03033CISQE/NOPB Datasheet - Page 18
![IC CLOCK CONDITIONER PREC 48LLP](/photos/6/51/65163/pkg_sqa48a_sml.jpg)
LMK03033CISQE/NOPB
Manufacturer Part Number
LMK03033CISQE/NOPB
Description
IC CLOCK CONDITIONER PREC 48LLP
Manufacturer
National Semiconductor
Type
Clock Conditionerr
Datasheet
1.LMK03000DISQENOPB.pdf
(30 pages)
Specifications of LMK03033CISQE/NOPB
Pll
Yes
Input
Clock
Output
LVDS, LVPECL
Number Of Circuits
1
Ratio - Input:output
1:4
Differential - Input:output
Yes/Yes
Frequency - Max
2.1GHz
Divider/multiplier
Yes/No
Voltage - Supply
3.15 V ~ 3.45 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-LLP
Frequency-max
2.1GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
LMK03033CISQETR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LMK03033CISQE/NOPB
Manufacturer:
NS
Quantity:
464
Part Number:
LMK03033CISQE/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
www.national.com
2.3.4 CLKoutX_DLY[3:0] -- Clock Output Delays
These bits control the delay stages for each clock output. In
order for these delays to be active, the respective
CLKoutX_MUX (See 2.3.2) bit must be set to either "Delayed"
or "Divided and Delayed" mode. By adding the delay block to
the output path a fixed delay of approximately 400 ps is in-
curred in addition to the delay shown in the table below.
2.3.5 CLKoutX_EN bit -- Clock Output Enables
These bits control whether an individual clock output is en-
abled or not. If the EN_CLKout_Global bit (See 2.8.4) is set
to zero or if GOE pin is held low, all CLKoutX_EN bit states
will be ignored and all clock outputs will be disabled.
2.4 REGISTER R8
The programming of register R8 provides optimum phase
noise performance.
2.5 REGISTER R9
The programming of register R9 is optional. If it is not pro-
grammed the bit Vboost will be defaulted to 0, which is the
test condition for all electrical characteristics.
2.5.1 Vboost -- Voltage Boost
By enabling this bit, the voltage output levels for all clock out-
puts is increased. Also, the noise floor is improved
CLKoutX_EN
CLKoutX_DLY[3:0]
Vboost
bit
0
1
0
1
10
11
12
13
14
15
0
1
2
3
4
5
6
7
8
9
EN_CLKout_Global bit = 1
GOE pin = High / No
Voltage Output
Typical LVDS
Conditions
Connect
(mV)
350
390
Delay (ps)
0 (default)
Typical LVPECL
Voltage Output
1050
1200
1350
1500
1650
1800
1950
2100
2250
150
300
450
600
750
900
CLKoutX
Disabled
(mV)
(default)
Enabled
810
865
State
18
2.6 REGISTER R11
This register only has one bit and only needs to be pro-
grammed in the case that the phase detector frequency is
greater than 20 MHz and digital lock detect is used. Other-
wise, it is automatically defaulted to the correct values.
2.6.1 DIV4 -- High Phase Detector Frequencies and Lock
Detect
This bit divides the frequency presented to the digital lock de-
tect circuitry by 4. It is necessary to get a reliable output from
the digital lock detect output in the case of a phase detector
frequency frequency greater than 20 MHz.
2.7 REGISTER R13
2.7.1 VCO_C3_C4_LF[3:0] -- Value for Internal Loop Filter
Capacitors C3 and C4
These bits control the capacitor values for C3 and C4 in the
internal loop filter.
2.7.2 VCO_R3_LF[2:0] -- Value for Internal Loop Filter
Resistor R3
These bits control the R3 resistor value in the internal loop
filter. The recommended setting for VCO_R3_LF[2:0] = 0 for
optimum phase noise and jitter.
VCO_C3_C4_LF[3:0]
DIV4
VCO_R3_LF[2:0]
0
1
12 to 15
5 to 7
10
11
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
Phase Detector Frequency
Phase Detector Frequency > 20 MHz
Digital Lock Detect Circuitry Mode
0 (default)
Divided by 4
Not divided
C3 (pF)
Loop Filter Capacitors
Low (~600 Ω) (default)
100
100
100
150
150
50
50
50
0
0
0
R3 Value (kΩ)
Invalid
Invalid
≤
10
20
30
40
20 MHz (default)
10 (default)
C4 (pF)
110
110
110
160
160
110
60
10
10
60
60