ICS650GI-44LFT IDT, Integrated Device Technology Inc, ICS650GI-44LFT Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
ICS650GI-44LFT
Manufacturer Part Number
ICS650GI-44LFT
Description
IC CLK SYNTHESIZER 16-TSSOP
Manufacturer
IDT, Integrated Device Technology Inc
Type
Clock/Frequency Synthesizerr
Datasheet
1.ICS650GI-44LFT.pdf
(11 pages)
Specifications of ICS650GI-44LFT
Pll
Yes
Input
Clock, Crystal
Output
CMOS
Number Of Circuits
1
Ratio - Input:output
1:3
Differential - Input:output
No/No
Frequency - Max
50MHz
Divider/multiplier
No/No
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP
Frequency-max
50MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
650GI-44LFT
Pin Descriptions
External Components
Decoupling Capacitor
As with any high-performance mixed-signal IC, the
ICS650-44 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01µF must be connected
between each VDD and the PCB ground plane.
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50 trace (a commonly
used trace impedance), place a 33 resistor in series with
the clock line, as close to the clock output pin as possible.
The nominal impedance of the clock output is 20 .
Crystal Load Capacitors
The device crystal connections should include pads for
IDT™ / ICS™ SPREAD SPECTRUM CLOCK SYNTHESIZER
ICS650-44
SPREAD SPECTRUM CLOCK SYNTHESIZER
Number
Pin
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
Pin Name
X1/CLKIN
VDDO
PDTS
GND
GND
VDD
VDD
VDD
50M
50M
50M
FS0
FS1
FS3
FS2
X2
Output
Output
Output
Output
Power
Power
Power
Power
Power
Power
Type
Input
Input
Input
Input
Input
Input
Pin
Crystal input. Connect this pin to a 25 MHz crystal or external input
clock.
Select pin 0. Internal pull-up resistor. See table on page 2.
Select pin 1. Internal pull-up resistor. See table on page 2.
Spread Spectrum output. Weak internal pull-down when tri-stated.
Connect to +3.3 V.
Connect to ground.
Select pin 3. Internal pull-up resistor. See table on page 2.
Spread Spectrum output. Weak internal pull-down when tri-stated.
Spread Spectrum output. Weak internal pull-down when tri-stated.
Connect to +2.5 V.
Connect to ground.
Connect to +3.3 V.
Select pin 2. Internal pull-up resistor. See table on page 2.
Powers down entire chip. Tri-states CLK outputs when low. Internal
pull-up.
Connect to +3.3 V.
Crystal Output. Connect this pin to a 25 MHz crystal. Do not connect if
clock input is used.
3
small capacitors from X1 to ground and from X2 to ground.
These capacitors are used to adjust the stray capacitance of
the board to match the nominally required crystal load
capacitance. Because load capacitance can only be
increased in this trimming process, it is important to keep
stray capacitance to a minimum by using very short PCB
traces (and no vias) between the crystal and device. Crystal
capacitors must be connected from each of the pins X1 and
X2 to ground.
The value (in pF) of these crystal caps should equal (C
pF)*2. In this equation, C
Example: For a crystal with a 16 pF load capacitance, each
crystal capacitor would be 20 pF [(16-6) x 2] = 20.
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
Pin Description
L
= crystal load capacitance in pF.
CLOCK SYNTHESIZER
ICS650-44
REV E 051310
L
-6