DS1086LU+T Maxim Integrated Products, DS1086LU+T Datasheet - Page 9
![IC ECONOSILL 3.3V SS 8-USOP](/photos/1/39/13936/406-8-msop_sml.jpg)
DS1086LU+T
Manufacturer Part Number
DS1086LU+T
Description
IC ECONOSILL 3.3V SS 8-USOP
Manufacturer
Maxim Integrated Products
Series
EconOscillator™r
Type
Spread Spectrum Clock Generatorr
Datasheet
1.DS1086LU-533.pdf
(16 pages)
Specifications of DS1086LU+T
Pll
No
Input
Clock
Output
Clock
Number Of Circuits
1
Ratio - Input:output
2:1
Differential - Input:output
No/No
Frequency - Max
48.75MHz
Divider/multiplier
Yes/No
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Frequency-max
66MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
A block diagram of the DS1086L is shown in Figure 3.
The internal master oscillator generates a square wave
with a 33.3MHz to 66.6MHz frequency range. The fre-
quency of the master oscillator can be programmed
with the DAC register over a two-to-one range in 5kHz
steps. The master oscillator range is larger than the
range possible with the DAC step size, so the OFFSET
register is used to select a smaller range of frequencies
over which the DAC spans. The prescaler can then be
set to divide the master oscillator frequency by 2
(where x equals 0 to 8) before routing the signal to the
output (OUT) pin.
A programmable triangle-wave generator injects an off-
set element into the master oscillator to dither its output
0.5%, 1%, 2%, 4%, or 8%. The dither magnitude is con-
trolled by the JS2, JS1, and JS0 bits in the PRESCALER
word and enabled with the SPRD pin. Futhermore, the
dither rate is controlled by the JS4 and JS3 bits in the
PRESCALER word and determines the frequency of the
dither. The maximum spectral attenuation occurs when
the prescaler is set to 1 and is reduced by 2.7dB for
every factor of 2 that is used in the prescaler. This hap-
Figure 3. Block Diagram
_______________________________________________________________________________________
Detailed Description
SPRD
GND
PDN
3.3V Spread-Spectrum EconOscillator
SDA
V
SCL
OE
CC
V
CC
INTERFACE
2-WIRE
TRIANGLE WAVE
CONTROL
GENERATOR
DITHER
DAC
PRESCALER
EEPROM CONTROL
OFFSET
RANGE
REGISTERS
ADDR
DITHER SIGNAL
x
pens because the prescaler’s divider function tends to
average the dither in creating the lower frequency.
However, the most stringent spectral emission limits are
imposed on the higher frequencies where the prescaler
is set to a low divider ratio.
The external control input, OE, gates the clock output
buffer. The PDN pin disables the master oscillator and
turns off the clock output for power-sensitive applica-
tions*. On power-up, the clock output is disabled until
power is stable and the master oscillator has generated
512 clock cycles. Both controls feature a synchronous
enable that ensures there are no output glitches when
the output is enabled.
The control registers are programmed through a 2-wire
interface and are used to determine the output frequen-
cy and settings. Once programmed into EEPROM,
since the register settings are NV, the settings only
need to be reprogrammed if it is desired to reconfigure
the device.
* The power-down command must persist for at least two out-
put frequency cycles plus 10µs for deglitching purposes.
VOLTAGE-CONTROLLED
BY 1, 2, 4...256
PRESCALER
OSCILLATOR
DAC
CONTROL VOLTAGE
DS1086L
FREQUENCY
MASTER
OSCILLATOR
OUTPUT
OUT
9