DS1086Z+T&R Maxim Integrated Products, DS1086Z+T&R Datasheet - Page 5
![IC ECONOSILL 3.3V SS 8-SOIC](/photos/1/39/13902/8-soic_21-0042b_sml.jpg)
DS1086Z+T&R
Manufacturer Part Number
DS1086Z+T&R
Description
IC ECONOSILL 3.3V SS 8-SOIC
Manufacturer
Maxim Integrated Products
Series
EconOscillator™r
Type
Spread Spectrum Clock Generatorr
Datasheet
1.DS1086Z.pdf
(14 pages)
Specifications of DS1086Z+T&R
Pll
No
Input
Clock
Output
Clock
Number Of Circuits
1
Ratio - Input:output
2:1
Differential - Input:output
No/No
Divider/multiplier
Yes/No
Voltage - Supply
4.75 V ~ 5.25 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Frequency-max
133MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AC ELECTRICAL CHARACTERISTICS: 2-WIRE INTERFACE (continued)
(V
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
Note 10:
Note 11:
Note 12:
Note 13:
Note 14:
Note 15:
Note 16:
Note 17:
Setup Time for STOP
Capacitive Load for Each Bus
Line
NV Write-Cycle Time
Input Capacitance
CC
= 5V ±5%, T
PARAMETER
All voltages are referenced to ground.
DAC and OFFSET register settings must be configured to maintain the master oscillator frequency within this range.
Correct operation of the device is not guaranteed if these limits are exceeded.
This is the absolute accuracy of the master oscillator frequency at the default settings.
This is the change that is observed in master oscillator frequency with changes in voltage from nominal voltage at
T
This is the percentage frequency change from the +25°C frequency due to temperature at V
perature change varies with the master oscillator frequency setting. The minimum occurs at the default master oscillator
frequency (f
(see Figure 2).
The dither deviation of the master oscillator frequency is unidirectional and lower than the undithered frequency.
The integral nonlinearity of the frequency adjust DAC is a measure of the deviation from a straight line drawn between the
two endpoints of a range. The error is in percentage of the span.
This is true when the prescaler = 1.
Frequency settles faster for small changes in value. During a change, the frequency transitions smoothly from the original
value to the new value.
This indicates the time elapsed between power-up and the output becoming active. An on-chip delay is intentionally
introduced to allow the oscillator to stabilize. t
depends on the programmed clock frequency.
Output voltage swings can be impaired at high frequencies combined with high output loading.
A fast-mode device can be used in a standard-mode system, but the requirement t
This is automatically the case if the device does not stretch the LOW period of the SCL signal. If such a device does
stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line at least t
1000ns + 250ns = 1250ns before the SCL line is released.
After this period, the first clock pulse is generated.
A device must internally provide a hold time of at least 300ns for the SDA signal (referred to as the V
nal) in order to bridge the undefined region of the falling edge of SCL.
The maximum t
C
Typical frequency shift due to aging is ±0.5%. Aging stressing includes Level 1 moisture reflow preconditioning (24hr
+125°C bake, 168hr 85°C/85%RH moisture soak, and 3 solder reflow passes +240 +0/-5°C peak) followed by 1000hr
max V
121°C/2 ATM Steam/Unbiased Autoclave.
A
B
—total capacitance of one bus line, timing referenced to 0.9 x V
= +25°C.
CC
A
= 0°C to +70°C.)
biased 125°C HTOL, 1000 temperature cycles at -55°C to +125°C, 96hr 130°C/85%RH/5.5V HAST and 168hr
default
HD:DAT
). The maximum occurs at the extremes of the master oscillator frequency range (66MHz or 133MHz)
need only be met if the device does not stretch the LOW period (t
SYMBOL
t
SU:STO
t
C
WR
C
Spread-Spectrum EconOscillator
B
I
_____________________________________________________________________
Fast mode
Standard mode
(Note 16)
stab
is equivalent to approximately 512 master clock cycles and therefore
CONDITION
CC
and 0.1 x V
CC
SU:DAT
.
MIN
0.6
4.0
LOW
> 250ns must then be met.
CC
) of the SCL signal.
TYP
= 5V. The maximum tem-
5
R MAX
IH MIN
+ t
MAX
400
10
SU:DAT
of the SCL sig-
UNITS
=
ms
pF
pF
µs
5