1-215079-8 TE Connectivity, 1-215079-8 Datasheet
1-215079-8
Specifications of 1-215079-8
Available stocks
Related parts for 1-215079-8
1-215079-8 Summary of contents
Page 1
... Tyco Electronics Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA *Trademark R6-76 (Rev. 07-01) DATE 28/10 /98 APVD M.Gosselink This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. 108 - 19052 19/Jun/06 Rev ...
Page 2
... Products shall be of design, construction and physical dimensions as specified on the applicable product drawings. All connector types of the Micro-MaTch Miniature connector System are available from positions (only even numbers ) Centerline distance between contacts is 1,27 mm (0,50” multiple of this case of selectively loaded connectors, which are available for all versions. 3.2 Material and Finish: Contacts: Phosphor Bronze according DIN specifications, tinplated over nickel underlayer ...
Page 3
... Wire-to-board and/or Board-to-board connections with the connector system positioned on the solder side of the PC board -for instance Surface Mount Application- • Permanent connections of ribbon cable to PC board, using the Paddle board connector version. • Wire-to board connection with discrete wires. Rev. F R6-77 (Rev. 07-01) 108-19052 Page ...
Page 4
... COSI- cable specification The Micro-MaTch COSI connector is designed for untwisted discrete wires in the range from 20-28 AWG. - Maximum insulation diameter for wires between 20-24 AWG is ∅ 0. Maximum insulation diamter for wires between 24-28 AWG is ∅ 1.27 mm 3.6 Performance and Test description Ratings: − ...
Page 5
... SMD Female Top Entry with Male On Wire Paddle board Crimp on Snap In Rev. F R6-77 (Rev. 07-01 Ambient Temperature (°C) Female Top Entry with Male On Board B valid for: Female Top Entry with Male On Wire Female Side Entry with Male On Board SMD inboard with Male On Wire 108-19052 100 105 Page ...
Page 6
... Para 2.4.2. ( Reflow soldering method ) In acc. with: Tyco Test Spec 109-201 Reflow curve § 3.4.B.2. Procedures In acc. with IEC 512-2 test 3a. In acc. with IEC 512-2 test 4a. In acc. with IEC 512-2 test 2a. Under dry circuit conditions. All contacts measured. Page ...
Page 7
... Minimum time between 2 operations: 1 sec. 108-19052 In acc. With IEC 512-2 test 2a Under dry circuit conditions All contacts measured. In acc. With IEC 912 test 2a Under dry circuit conditions All contacts measured. In acc. With IEC 512-2 test 2a Under dry circuit conditions All contacts measured. ...
Page 8
... In acc. with IEC 512-7 test 13a (COSI 13b) In acc. with IEC 512-4 test 6d. In acc. with IEC 68-2-6 test Fc.procedure 8.2.1 At push in forces connecors must be supported by a part of the application tooling. ...
Page 9
... Paragraph 3.6.1 3.6.8 3.6.22 3.6.21 3.6.24 3.6.22 3.6.8 3.6.1 3.6.1 3.6.16 3.6.8 3.6.16 3.6.13 3.6.10 3.6.8 3.6.21 3.6.8 3.6.10 3.6.1 3.6.1 3.6.8 3.6.25 3.6.8 3.6.17 3.6.8 3.6.1 3.6.1 3.6.2 3.6.1 3.6.1 3.6.3 3.6.1 3.6.1 3.6.14 3.6.25 3.6.14 3.6.1 3.6.12 Page ...
Page 10
... Paragraph 3.6.1 3.6.9 3.6.22 3.6.21 3.6.24 3.6.22 3.6.9 3.6.1 3.6.1 3.6.9 3.6.13 3.6.9 3.6.13 3.6.9 3.6.1 3.6.1 3.6.9 3.6.25 3.6.9 3.6.1 Page ...
Page 11
... Termination strength in Newtons 108-19052 3.6.1 3.6.18 3.6.1 3.6.1 3.6.9 3.6.22 3.6.9 3.6.1 3.6.1 3.6.12 3.6.1 Paragraph 3.6.1 3.6.11 3.6.23 3.6.21 3.6.24 3.6.21 3.6.11 3.6.1 3.6.1 3.6.11 3.6.25 3.6.11 3.6.1 3.6.1 3.6.2 3.6.1 3.6.1 3.6.11 3.6.3 3.6.11 3.6.1 3.6.1 3.6.15 3.6.1 Page ...
Page 12
... Paragraph 3.6.1 3.6.10 3.6.6 3.6.7 3.6.23 3.6.21 3.6.24 3.6.21 3.6.10 3.6.6 3.6.7 3.6.25 3.6.10 3.6.6 3.6.7 3.6.1 3.6.1 3.6.11 3.6.25 3.6.10 3.6. 3.6.10 3.6.1 3.6.1 3.6.10 3.6.25 3.6.10 3.6.17 3.6.10 3.6.1 Page ...
Page 13
... Termination resistance 108-19052 Paragraph 3.6.1 3.6.12 3.6.1 3.6.1 3.6.4 3.6.1 3.6.1 3.6.5 3.6.1 Paragraph 3.6.1 3.6.8 3.6.23 3.6.21 3.6.24 3.6.21 3.6.8 3.6.1 3.6.1 3.6.16 3.6.8 3.6.13 3.6.16 3.6.8 3.6.21 3.6.16 3.6.8 3.6.1 3.6.1 3.6.8 3.6.25 3.6.8 3.6.17 3.6.8 3.6.1 3.6.1 3.6.12 Page ...
Page 14
... Damp heat cyclic, first cycle c) Cold d) Damp Heat cyclic, remaining 5 cycles 5. 6. Voltage proof 7. Visual examination 4. Rev. F R6-77 (Rev. 07-01) Measurements Insulation resistance Insulation resistance 108-19052 Paragraph 3.6.1 3.6.1 3.6.22 3.6.1 3.6.1 3.6.6 3.6.7 3.6.23 3.6.21 3.6.24 3.6.21 3.6.6 3.6.7 3.6.1 Page ...
Page 15
... At least 5 connectors of the 6 positions or at least 30 contacts shall be used for each testgroup. 4.1.2 Test sequence Qualification inspection shall be verified by testing samples as specified in spec. 108-19052 Par 3.7. 4.2 Requalification testing If changes significantly affecting form, fit or function are made to the product or the manufacturing process, product assurance shall co-ordinate requalification testing, consisting of all or part of the original testing sequence as determined by development/product, quality and reliability engineering ...