DS1338U-33+ Maxim Integrated Products, DS1338U-33+ Datasheet - Page 7
![IC RTC 56BYTE NV RAM 3.3V 8-USOP](/photos/1/39/13936/406-8-msop_sml.jpg)
DS1338U-33+
Manufacturer Part Number
DS1338U-33+
Description
IC RTC 56BYTE NV RAM 3.3V 8-USOP
Manufacturer
Maxim Integrated Products
Type
Clock/Calendar/NVSRAMr
Datasheet
1.DS1338Z-33.pdf
(16 pages)
Specifications of DS1338U-33+
Memory Size
56B
Time Format
HH:MM:SS (12/24 hr)
Date Format
YY-MM-DD-dd
Interface
I²C, 2-Wire Serial
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Function
Clock/Calendar
Rtc Memory Size
56 Byte
Supply Voltage (max)
5.5 V
Supply Voltage (min)
3 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Rtc Bus Interface
Serial (I2C)
Supply Current
325 uA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PIN DESCRIPTION
DETAILED DESCRIPTION
The DS1338 serial RTC is a low-power, full BCD clock/calendar plus 56 bytes of NV SRAM. Address and data are
transferred serially through an I
month, and year information. The end of the month date is automatically adjusted for months with fewer than 31
days, including corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM
indicator. The DS1338 has a built-in power-sense circuit that detects power failures and automatically switches to
the V
—
8
1
2
3
4
5
6
7
8
BAT
PIN
supply.
4–13
16
14
15
16
—
—
1
2
3
SQW/OUT
NAME
GND
SDA
SCL
N.C.
V
V
X1
X2
BAT
CC
2
C interface. The clock/calendar provides seconds, minutes, hours, day, date,
32.768kHz Crystal Connections. The internal oscillator circuitry is designed for
operation with a crystal having a specified load capacitance (C
external 32.768kHz oscillator can also drive the DS1338. In this configuration,
the X1 pin is connected to the external oscillator signal and the X2 pin is
floated.
Note: For more information about crystal selection and crystal layout considerations,
refer to Application Note 58: Crystal Considerations with Dallas Real-Time Clocks.
Backup Supply Input for Lithium Cell or Other Energy Source. Battery voltage
must be held between the minimum and maximum limits for proper operation.
Diodes placed in series between the backup source and the V
prevent proper operation. If a backup supply is not required, V
grounded. UL recognized to ensure against reverse charging when used with a
lithium cell. For more information, visit www.maxim-ic.com/qa/info/ul.
Ground. DC power is provided to the device on these pins. V
power input. When voltage is applied within normal limits, the device is fully
accessible and data can be written and read. When a backup supply is
connected to the device and V
However, the timekeeping function continues unaffected by the lower input
voltage.
Serial Data. Input/output pin for the I
output and requires an external pullup resistor. The pull up voltage may be up
to 5.5V regardless of the voltage on V
Serial Clock. Input pin for the I
movement on the serial interface. The pull up voltage may be up to 5.5V
regardless of the voltage on V
Square-Wave/Output Driver. When enabled and the SQWE bit set to 1, the
SQW/OUT pin outputs one of four square-wave frequencies (1Hz, 4kHz, 8kHz,
32kHz). It is an open drain output and requires an external pullup resistor.
Operates with either V
5.5V regardless of the voltage on V
Primary Power Supply. When voltage is applied within normal limits, the device
is fully accessible and data can be written and read. When a backup supply is
connected to the device and V
The backup supply maintains the timekeeping function while V
No Connection. These pins are not connected internally, but must be grounded
for proper operation.
7 of 16
CC
or V
BAT
CC
2
CC
CC
C serial interface. Used to synchronize data
.
applied. The pull up voltage may be up to
is below V
is below V
FUNCTION
CC
2
C serial interface. It is an open drain
. If not used, this pin may be left floating.
CC
.
DS1338 I
PF
PF
, reads and writes are inhibited.
, reads and writes are inhibited.
2
C RTC with 56-Byte NV RAM
CC
BAT
BAT
CC
L
) of 12.5pF. An
is the primary
is absent.
pin may
must be