2-179694-4 TE Connectivity, 2-179694-4 Datasheet
2-179694-4
Specifications of 2-179694-4
Related parts for 2-179694-4
2-179694-4 Summary of contents
Page 1
... AMP Common Termination (CT), Connector 1. Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods and quality assurance provisions of AMP Common Termination (CT), Connector, 2mm Pitch, M/T Type. The applicable product description and part numbers are as shown in Fig.1: Product Part No. X-173977-X X-179694-X 2. ...
Page 2
... Pretinned Brass (0.8um min. thick solder-plated over 0.5um min. thick copper underplate) : 6/6 Nylon (UL94 V-0) : Brass (0.2um min. thick Au Plated over 1~2um thick Nickel underplate) : 6/6 Nylon GF Type (UL94 V-0) : Pretin lead Brass (0.8um min. thick solder-plated over 0.5um min. ...
Page 3
... Performance Requirements and Test Descriptions: The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig.2, Para. 3.8. All tests shall be performed at ambient temperature unless otherwise specified. Tyco Electronics AMP Shanghai Ltd. ...
Page 4
... Fig. 2 (To be continued) PAGE Document No Procedures Subject terminated connector and header to mate and unmate to measure the force required to engage and disengage by operating the head at a rate minute. Record by using autograph. Lock Side. 7.84 9.80 12 ...
Page 5
... Direction (AWG) [Min.] [Min.] Unit: N Unit 7 & #24 7.8 14.7N Min. per contact. Fig. 2 (To be continued) PAGE Document No Procedures After preconditioning by using applicable post for 3 cycles, measure the force required to unmate post by operating the head at a rate of 50mm a minute. Apply a pull-off load to ...
Page 6
... Connector must withstand test potential of 1.0 kV (AC) for 1 minute. Current leakage must be 5.0mA Max. 1000 M Min. (Initial max. under loaded specified current. See Fig. 3. Fig. 2 (To be continued) PAGE Document No Procedures By using AMP recommended panel cut-out layout dimensions, specified in AMP Customer Drawing, measure the force required to mount header into the panel ...
Page 7
... Resistance (low level) (Final) must meet visual & electrical requirements, which applicable. Fig. 2 (To be continued) PAGE Document No Procedures Subject mated connectors to 10-55 traversed in 1 minute at 1.52 mm amplitude 2 hours each of 3 mutually perpendicular planes. MIL-STD-202, Method 201, Condition A. Subject mated connectors to 490.3 2 m/s halfsine shock pulses of 11milisecond duration ...
Page 8
... PAGE Document No Procedures Subject mated connectors to sulfurous acid gas atmosphere of 3±1ppm concentration at o 40±2 C for 240 hours. Subsequent measurement shall be done after reconditioning in the room temperature for 1 hour. Subject contacts to solderability testing, as specified. MIL-STD-202, Method 208. Subject product mounted on printed circuit boards to solder o bath at 260± ...
Page 9
... Fig.5 Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig.3 Fig.4 Fig.6 Fig.7 PAGE Document No 108-5218 REV LOC S ES ...
Page 10
... The test specimens to be used for the performance evaluation testing, shall be prepared in accordance with AMP Application Specification, 114-5104, Termination of AMP CT Connector Pitch, M/T Type, by using the samples selected from the current production at random, and conforming to the requirements of the applicable product drawing. ...
Page 11
... X-177626-X Post Header, Horizontal (H), Short Tine, Box Type X-175694-X Post Header, w/Panel Lock, for Relay Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B PAGE Document No 108-5218 No. of Pos. 2~15 Pos. 2~15 Pos. 2~15 Pos. 2~15 Pos. 2~15 Pos. 2~15 Pos. 2~15 Pos. ...
Page 12
... Pos. 6 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 3 Pos. 3 Pos. 2~6, 8 Pos. 2~6, 8 Pos. 2~5 Pos. 2~5 Pos. 2~6, 8 Pos 8~11 Pos. 3 Pos. 7~10, 13 Pos. 2~8 Pos. 2~8 Pos. 2 Pos. 3 Pos. 3 Pos. 2~8 Pos. 2~8 Pos. REV LOC S ...