2-353293-0 TE Connectivity, 2-353293-0 Datasheet
2-353293-0
Specifications of 2-353293-0
Available stocks
Related parts for 2-353293-0
2-353293-0 Summary of contents
Page 1
... AMP Specifications: A. 109-5000 : Test Specification, General Requirements for Test Methods B. 114-5223 : Apprication Specification C. 501-5269 : Test Report 2.2 Commercial Standards and specifications : A. MIL-STD-202 : Test Methods for Electronic and Electrical Component Parts. B. IEC : International Electrotechnical Commission G R EVISED D 20051225211245_409482 DIST LTR REVISION RECORD ...
Page 2
... Housing : 66 Nylon NON G.F.(UL94V-O) Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Pre tin-Lead plated Brass (0.8µm min .thick tin-lead plating over 0.5µm min.thick (3µm min thick tin-lead plating over 3µm min.thick copper underplating) PAGE Document No. REV 108-5525 LOC A ES ...
Page 3
... Ratings: A. Voltage Rating :50 VAC/DC B. Current Rating(Maximum) AWG #26 :2A, AWG #28 :1A C. Temperature Rating :－ 30°C to +105°C The upper limit of the temperature includes the temperature rising resulted by the energized electrical current. 3.4 Applicable Wires A. Applicable Wire Size: AWG #28,#26 (0.08～ 0.14mm B ...
Page 4
... Fig. 2 (To be continued) PAGE Document No. 108-5525 Procedures Visual inspection No physical damage Subject mated contacts assembled in housing Max open circuit at 10 mA. Fig.4. 500 VAC for 1 minute. Test between adjacent circuits of mated connectors. MIL STD 202 TEST METHOD 301 Impressed voltage 500 VDC for 1 minute ...
Page 5
... N(1.0 kgf) Min. 4.9 N(0.5 kgf) Min. 49 N(5 kgf ) MAX. 83.3 N(8.5 kgf) Min. See Fig.12 20 mΩ Max. (Final) Fig. 2 (To be continued) PAGE Document No Procedures Apply a pull-off load to terminated wire of contact secured on the tester, Operation Speed : 50 mm/min. ...
Page 6
... Max.(Final) Wet Solder Coverage : 90 % Min. Fig. 2 (To be continued) PAGE Document No Procedures Subject mated connectors to 10-55-10 Hz traversed in 1 minute at 1.52 mm amplitude 2 hours each of 3 mutually perpendicular planes applied. MIL-STD-202 TEST METHOD 201 CONDITION A IEC 68-2-6 Mounting : Fig. 9 Accelerated Velocity : ...
Page 7
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Requirements No physical damege shall Flow Soldering occur. Test connector on PCB. Solder Temerature : 260 ± 5 °C Immersion Duration : 10 ± 1 sec. Reflow Soldering Reflow Soldering by next conditions. Preheat:100～ 150℃ 60sec. Min. Heating:210 Peak Temperature:240 ...
Page 8
... Max. (Final) Mated connector － 40 ± 3 °C, 500 hours IEC 68-2-1 20 mΩ Max. (Final) Mated connector SO2 Gas : 10 ± 3 ppm R.H. 35 ± 2 °C, 240 hours 20 mΩ Max. (Final) Mated connector H2S Gas : 3 ppm,40 ± 3 ℃ R.H.、 240 hours 20 mΩ ...
Page 9
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Test Group Test Sequence (a) 1,6 1,3 1,3 1,3 1,3 1,3 1,3 1,3 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2 Fig.3 (To be continued) PAGE Document No. 108-5525 2,4 2,4 2,4 2,4 2,4 2,4 2,4 2 REV LOC ...
Page 10
... Industrial Ammonia Gas Resistance to Solvent (a) Numbers indicate sequence in which the tests are performed. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Test Group Test Sequence (a) 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,4 2,4 2,4 2,4 2,4 2,4 2,4 2 Fig.3 (End) PAGE Document No ...
Page 11
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 4 Fig. 5 Fig. 6 PAGE Document No. 108-5525 REV LOC A ES ...
Page 12
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 7 Fig. 8 PAGE Document No. 108-5525 REV LOC A ES ...
Page 13
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 10 PAGE Document No. 108-5525 REV LOC A ES ...
Page 14
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 11 PAGE Document No. 108-5525 REV LOC A ES ...
Page 15
... Note : To be applied same specification to post header relay panel mount type by measurement on opposite lock side. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Unmating Force N (kgf) min. 2.99 ) 4.508 ( 0 ...
Page 16
... Single Row Post Header Assembly(V) DIP Staggered Type Without Boss Without Kink 2～ 20 Pos. Tube Packing for Single Row Post Header Assembly (V) DIP Staggered Type Without Boss Without Kink 2～ 20 Pos. Single Row Post Header Assembly (V) SMT Type With Boss 3～ 20 Pos. ...
Page 17
... Type Without Boss 2～ 20 Pos. Duble Row Post Header Assembly (V) DIP Staggered Type With Boss With Kink 22～ 40 Pos.(Only Even Number Pos.) Double Row Post Header Assembly (V) SMT Type With Boss 22～ 40 Pos.(Only Even Number Pos.) Double Row Post Header Assembly Panel Mount Type 22～ ...