MCP3301-BI/SN Microchip Technology, MCP3301-BI/SN Datasheet
MCP3301-BI/SN
Specifications of MCP3301-BI/SN
Available stocks
Related parts for MCP3301-BI/SN
MCP3301-BI/SN Summary of contents
Page 1
... The reference voltage can be varied from 400 mV to 5V, yielding input-referred resolution between 98 µV and 1.22 mV. The MCP3301 is available in 8-pin PDIP, 150 mil SOIC and MSOP packages. The full differential inputs of this device enable a wide variety of signals to be used in applications such as remote data acquisition, portable instrumentation and battery operated applications ...
Page 2
... MCP3301 Functional Block Diagram V REF CDAC Comparator - IN+ Sample & Hold IN- Circuits + Control Logic CS/SHDN CLK DS21700C-page 13-Bit SAR Shift Register D OUT © 2007 Microchip Technology Inc. ...
Page 3
... Full differential input SS REF SAMPLE Units Conditions ksps Note 8 ksps 2.7V, V =1.35V DD REF CM CLK periods CLK periods bits LSB MCP3301-B MCP3301-C LSB Monotonic with no missing codes over temperature LSB LSB LSB dB Note 3 dB Note 3 dB Note 3 dB Note 6 dB Note 4 DS21700C-page 3 ...
Page 4
... MCP3301 ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: Unless otherwise noted, all parameters apply at V configuration (Figure 3-4) with fixed common mode voltage of 2.5V. All parameters apply over temperature with T = -40°C to +85°C (Note 7). Conversion speed (f AMB Parameter Symbol Reference Input Voltage Range ...
Page 5
... A θ — 206 — JA θ — 85 — JA θ — 163 — JA level. REF . Sign Bit Null Bit MCP3301 = 0V, and V = 5V. Full differential input SS REF SAMPLE Units Conditions V µ 5V, D unloaded , DD REF OUT 2.7V, D unloaded DD REF OUT µ 5.0V DD °C °C °C ° ...
Page 6
... MCP3301 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e ...
Page 7
... FIGURE 2-11: (DNL) vs. Sample Rate (V 2.0 V =2. 1.5 SAMPLE 1.0 0.5 0.0 -0.5 -1.0 -1.5 -2 FIGURE 2-12: (DNL) vs. V REF MCP3301 = 0V, SS =2.7V Positive INL Negative INL 0 50 100 150 Temperature (°C) Integral Nonlinearity (INL) = 2.7V). DD =2.7V Positive INL Negative INL ...
Page 8
... MCP3301 Note: Unless otherwise indicated 100 ksps 17*f SAMPLE CLK 1 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 -4096 -3072 -2048 -1024 0 1024 Code FIGURE 2-13: Differential Nonlinearity (DNL) vs. Code (Representative Part). 1.0 0.8 0.6 0.4 Positive DNL 0.2 0.0 -0.2 Negative DNL -0 ...
Page 9
... FIGURE 2-23: Distortion (SINAD) vs. Input Frequency =5V DD REF F = 100 ksps SAMPLE SAMPLE -40 -35 100 FIGURE 2-24: Distortion (SINAD) vs. Input Signal Level. MCP3301 = 0V =5V DD REF F = 100 ksps SAMPLE V =V =2.7V DD REF ksps SAMPLE 0 50 100 150 Temperature (°C) Offset Error vs. =2.7V REF = 50 ksps V ...
Page 10
... MCP3301 Note: Unless otherwise indicated 100 ksps 17*f SAMPLE CLK =2. ksps SAMPLE (V) REF FIGURE 2-25: Effective Number of Bits (ENOB) vs REF 100 =2.7V DD REF ksps 50 SAMPLE Input Frequency (kHz) FIGURE 2-26: Spurious Free Dynamic Range (SFDR) vs. Input Frequency. 0 -10 -20 -30 -40 -50 -60 -70 ...
Page 11
... FIGURE 2-34: 100 150 200 0 FIGURE 2-35 =2.7V 30 REF = 50 ksps 100 150 -50 FIGURE 2-36: MCP3301 = 0V 3.5 4 4 REF =5V DD REF V =V =2.7V DD REF 50 100 150 200 Sample Rate (ksps) I vs. Sample Rate. REF V =V =5V DD REF F = 100 ksps ...
Page 12
... MCP3301 Note: Unless otherwise indicated 100 ksps 17*f SAMPLE CLK 2.5 3 3.5 4 4.5 V (V) DD FIGURE 2-37 DDS DD 100 10 1 0.1 0.01 0.001 -50 - Temperature (°C) FIGURE 2-38: I vs. Temperature. DDS = 100 ksps 4 SAMPLE =2. ksps 1 SAMPLE (V) REF FIGURE 2-39: Negative Gain Error vs. ...
Page 13
... DUT Ω 1 kΩ Ω P-P Power Supply Sensitivity REF DD 1 µF 0.1 µF 0.1 µ IN(+) V V REF DD MCP3301 IN(-) Full Differential Test V =2.5V V =5V REF DD 1 µF 0.1 µF 0.1 µF IN(+) V V REF DD MCP3301 IN(-) V SS Pseudo Differential Test DS21700C-page 13 ...
Page 14
... MCP3301 4.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 4-1. TABLE 4-1: PIN FUNCTION TABLE. Name Function V Reference Voltage Input REF IN(+) Positive Analog Input IN(-) Negative Analog Input V Ground SS CS/SHDN Chip Select / Shutdown Input D Serial Data Out OUT CLK Serial Clock V +2 ...
Page 15
... For a 13-bit converter, the theoretical SNR limit is 80.02 dB. Total Harmonic Distortion - Total Harmonic Distortion is (THD) is the ratio of the rms sum of the harmonics to the fundamental, measured at the output of the con- verter. For the MCP3301 defined using the first 9 harmonics, as shown in the following equation: EQUATION ...
Page 16
... Simplified Block Diagram. DS21700C-page 16 6.2 Driving the Analog Input The analog input of the MCP3301 is easily driven either differentially or single-ended. Any signal that is com- mon to the two input channels will be rejected by the common mode rejection of the device. During the charging time of the sample capacitor, a small charging current will be required ...
Page 17
... Analog Input Model. 6.2.1 MAINTAINING MINIMUM CLOCK SPEED When the MCP3301 initiates, charge is stored on the sample capacitor. When the sample period is complete, the device converts one bit for each clock that is received important for the user to note that a slow clock rate will allow charge to bleed off the sample capacitor while the conversion is taking place ...
Page 18
... REF mode voltage. Using a 2.048V reference for the A/D converter, while biasing the input signal at 2.5V solves the problem. This circuit is shown in Figure 6-6. 10 kΩ 0.1 µF MCP606 1 kΩ MCP3301 IN IN- 1 µF V REF 1 MΩ 2.048V V V OUT IN 1 µF ...
Page 19
... Providing V devices in a “star” configuration can also reduce noise by eliminating current return paths and associated errors (Figure 6-10). For more information on layout tips when using the MCP3301 or other ADC devices, refer to AN-688 “Layout Tips for 12-Bit A/D Converter Applications” µ ...
Page 20
... MCP3301 7.0 SERIAL COMMUNICATIONS 7.1 Output Code Format The output code format is a binary two’s complement scheme with a leading sign bit that indicates the sign of the output. If the IN+ input is higher than the IN- input, the sign bit will be a zero. If the IN- input is higher, the sign bit will be a ‘ ...
Page 21
... Communicating with the MCP3301 Communication with the device is completed using a standard SPI compatible serial interface. Initiating com- munication with the MCP3301 begins with the CS going low. If the device was powered up with the CS pin low, it must be brought high and back low to initiate communication ...
Page 22
... Figure 7-5 show how the MCP3301 can be interfaced to a microcontroller with a standard SPI port. Since the MCP3301 always clocks data out on the falling edge of clock, the MCU SPI port must be configured to match this operation. SPI Mode 0,0 (clock idles low) and SPI Mode 1,1 (clock idles high) are both compatible with the MCP3301 ...
Page 23
... Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. © 2007 Microchip Technology Inc. MCP3301 : Example e 3301C 3 ...
Page 24
... MCP3301 8-Lead Plastic Micro Small Outline Package (MS) [MSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N NOTE Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length ...
Page 25
... Dimension Limits MIN N e .100 BSC A – A2 .115 A1 .015 E .290 E1 .240 D .348 L .115 c .008 b1 .040 b .014 eB – MCP3301 c NOM MAX 8 – .210 .130 .195 – – .310 .325 .250 .280 .365 .400 .130 .150 .010 .015 .060 .070 .018 .022 – .430 ...
Page 26
... MCP3301 8-Lead Plastic Small Outline (SN) – Narrow, 3.90 mm Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch Overall Height Molded Package Thickness § Standoff Overall Width Molded Package Width ...
Page 27
... APPENDIX A: REVISION HISTORY Revision C (January 2007) This revision includes updates to the packaging diagrams. © 2007 Microchip Technology Inc. MCP3301 DS21700C-page 27 ...
Page 28
... MCP3301 NOTES: DS21700C-page 28 © 2007 Microchip Technology Inc. ...
Page 29
... Plastic DIP (300 mil Body), 8-lead SN = Plastic SOIC (150 mil Body), 8-lead © 2007 Microchip Technology Inc. /XX Examples: Package a) MCP3301-BI/P: ±1 LSB INL, Industrial Temperature, PDIP package b) MCP3301-BI/SN: ±1 LSB INL, Industrial Temperature, SOIC package c) MCP3301-CI/MS: ±2 LSB INL, Industrial Temperature, MSOP package MCP3301 DS21700C-page29 ...
Page 30
... MCP3301 NOTES: DS21700C-page 30 © 2007 Microchip Technology Inc. ...
Page 31
... Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 32
... Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...