MCP3204-CI/SL Microchip Technology, MCP3204-CI/SL Datasheet
MCP3204-CI/SL
Specifications of MCP3204-CI/SL
Available stocks
Related parts for MCP3204-CI/SL
MCP3204-CI/SL Summary of contents
Page 1
... Low current design permits operation with typical standby and active currents of only 500 nA and 320 µA, respec- tively. The MCP3204 is offered in 14-pin PDIP, 150 mil SOIC and TSSOP packages. The MCP3208 is offered in 16-pin PDIP and SOIC packages. ...
Page 2
... V DD — — 50 ksps bits — ±0.75 ±1 LSB MCP3204/3208-B — ±1.0 ±2 MCP3204/3208-C — ±0.5 ±1 LSB No missing codes over-temperature — ±1.25 ±3 LSB — ±1.25 ±5 LSB — -82 — — 72 — — ...
Page 3
... REF MCP3204/3208 = REF Conditions V See Figure 4-1 See Figure ...
Page 4
... MCP3204/3208 ELECTRICAL SPECIFICATIONS (CONTINUED) Electrical Characteristics: Unless otherwise noted, all parameters apply -40°C to +85°C,f = 100 ksps and f AMB SAMPLE Parameters Sym Temperature Ranges Specified Temperature Range T A Operating Temperature T A Range Storage Temperature Range T A Thermal Package Resistance Thermal Resistance, ...
Page 5
... Waveform 2† * Waveform 1 is for an output with internal conditions such that the output is high, unless disabled by the output control. † Waveform 2 is for an output with internal conditions such that the output is low, unless disabled by the output control. FIGURE 1-3: MCP3204/3208 Waveform 2 DIS V /2 ...
Page 6
... MCP3204/3208 2.0 TYPICAL PERFORMANCE CHARACTERISTICS Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e ...
Page 7
... FIGURE 2-11: (DNL) vs. Sample Rate (V 3.0 2.0 1.0 0.0 -1.0 -2.0 -3 0.0 FIGURE 2-12: (DNL) vs. V REF MCP3204/3208 = 20 25°C. CLK SAMPLE A = 2.7 V REF = 50 ksps Positive INL Negative INL - 100 Temperature (°C) Integral Nonlinearity (INL) = 2.7V). ...
Page 8
... MCP3204/3208 Note: Unless otherwise indicated 1.0 0.8 0.6 0.4 0.2 0.0 -0.2 -0.4 -0.6 -0.8 -1.0 0 512 1024 1536 2048 2560 Digital Code FIGURE 2-13: Differential Nonlinearity (DNL) vs. Code (Representative Part). 1.0 0.8 0.6 0.4 Positive DNL 0.2 0.0 -0.2 -0.4 Negative DNL -0 ...
Page 9
... V REF 90 = 100 ksps 100 1 FIGURE 2-23: Distortion (SINAD) vs. Input Frequency REF 10 = 100 ksps 0 100 -40 -35 FIGURE 2-24: Distortion (SINAD) vs. Input Signal Level. MCP3204/3208 = 20 25°C. CLK SAMPLE REF F = 100 ksps SAMPLE 2 REF ksps SAMPLE - 100 Temperature (°C) Offset Error vs ...
Page 10
... MCP3204/3208 Note: Unless otherwise indicated 12.00 11.75 11.50 11.25 11. 10. 2 REF SAMPLE 10. ksps SAMPLE 10.25 10.00 9.75 9.50 9.25 9.00 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 V (V) REF FIGURE 2-25: Effective Number of Bits (ENOB) vs REF 100 SAMPLE 2 REF ksps ...
Page 11
... FIGURE 2-34: 100 10000 FIGURE 2-35: 100 100 -50 FIGURE 2-36: MCP3204/3208 = 20 25°C. CLK SAMPLE MHz except CLK = MHz DD CLK 3.0 3.5 4.0 4.5 5.0 5.5 6 REF REF 2 REF 100 1000 10000 Clock Frequency (kHz ...
Page 12
... MCP3204/3208 Note: Unless otherwise indicated REF 2.0 2.5 3.0 3.5 4.0 4.5 V (V) DD FIGURE 2-37 DDS DD 100. REF 10.00 1.00 0.10 0.01 -50 - Temperature (°C) FIGURE 2-38: I vs. Temperature. DDS DS21298C-page 5V 0V 100 ksps, f REF SS SAMPLE 2.0 1.8 1.6 1.4 1.2 1 ...
Page 13
... Conversion rates of 100 ksps are possible on the MCP3204/3208. See Section 6.2, “Maintaining Minimum Clock Speed”, for information on minimum clock rates. Communica- tion with the device is accomplished using a 4-wire SPI- compatible interface ...
Page 14
... MCP3204/3208 This diagram illustrates that the source impedance (R adds to the internal sampling switch (R directly effecting the time that is required to charge the capacitor (Csample). Consequently, larger source impedances increase the offset, gain and integral linearity errors of the conversion (see Figure 4-2). 4.2 ...
Page 15
... This is IN often done when dealing with microcontroller-based SPI ports that must send 8 bits at a time. Refer to Section 6.1 for more details on using the MCP3204/ 3208 devices with hardware SPI ports. 2002 Microchip Technology Inc. MCP3204/3208 ...
Page 16
... During this time, the bias circuit and the comparator power down while the reference input becomes a DATA high impedance node, leaving the CLK running to clock out LSB first data or zeroes. FIGURE 5-2: Communication with MCP3204 or MCP3208 in LSB First Format. DS21298C-page 16 t CYC Don’ ...
Page 17
... This is usually done by sending ‘leading zeros’ before the start bit example, Figure 6-1 and Figure 6-2 illustrate how the MCP3204/3208 can be interfaced to a MCU with a hardware SPI port. Figure 6-1 depicts the operation shown in SPI Mode 0,0, which requires that the SCLK from the MCU idles in the ‘ ...
Page 18
... MCP3204/3208 CS MCU latches data from A/D converter on rising edges of SCLK SCLK Data is clocked out of A/D converter on falling edges SGL/ D Start DIFF IN HI-Z D OUT Start Bit MCU Transmitted Data (Aligned with falling edge of clock) MCU Received Data (Aligned with rising ? ? ? ? ? ...
Page 19
... Figure 6-3, where an op amp is used to drive the analog input of the MCP3204/3208. This amplifier provides a low impedance source for the converter input, and a low pass filter, which eliminates unwanted high frequency noise ...
Page 20
... DS21298C-page 20 6.5 Utilizing the Digital and Analog Ground Pins The MCP3204/3208 devices provide both digital and analog ground connections to provide another means of noise reduction. As shown in Figure 6-5, the analog and digital circuitry is separated internal to the device. This reduces noise from the digital portion of the device being coupled into the analog portion of the device ...
Page 21
... Standard marking consists of Microchip part number, year code, week code, traceability code (facility code, mask rev#, and assembly code). For marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. 2002 Microchip Technology Inc. MCP3204/3208 Example: MCP3204-B I/P YYWWNNN Example: MCP3204-B XXXXXXXXXXX YYWWNNN Example: 3204-C IYWW NNN DS21298C-page 21 ...
Page 22
... MCP3204/3208 Package Marking Information (Continued) 16-Lead PDIP (300 mil) (MCP3304) XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN 16-Lead SOIC (150 mil) (MCP3304) XXXXXXXXXXXXX XXXXXXXXXXXXX YYWWNNN DS21298C-page 22 Example: MCP3208-B I/P YYWWNNN Example: MCP3208-B XXXXXXXXXX IYWWNNN 2002 Microchip Technology Inc. ...
Page 23
... L .125 .130 .135 c .008 .012 .015 B1 .045 .058 .070 B .014 .018 .022 eB .310 .370 .430 MCP3204/3208 MILLIMETERS MIN NOM MAX 14 2.54 3.56 3.94 4.32 2.92 3.30 3.68 0.38 7.62 7.94 8.26 6.10 6.35 6.60 18.80 19.05 19.30 3.18 3.30 3 ...
Page 24
... MCP3204/3208 14-Lead Plastic Small Outline (SL) – Narrow, 150 mil (SOIC Dimension Limits Number of Pins Pitch Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top ...
Page 25
... E1 .169 .173 .177 D .193 .197 .201 L .020 .024 .028 .004 .006 .008 B1 .007 .010 .012 MCP3204/3208 A2 MILLIMETERS* MIN NOM MAX 14 0.65 1.10 0.85 0.90 0.95 0.05 0.10 0.15 6.25 6.38 6.50 4.30 4.40 4.50 4.90 5.00 5.10 0.50 0.60 0. 0.09 ...
Page 26
... MCP3204/3208 16-Lead Plastic Dual In-line (P) – 300 mil (PDIP Dimension Limits Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane Shoulder to Shoulder Width Molded Package Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing § ...
Page 27
... L .016 .033 .050 .008 .009 .010 B .013 .017 .020 MCP3204/3208 A2 MILLIMETERS MIN NOM MAX 16 1.27 1.35 1.55 1.75 1.32 1.44 1.55 0.10 0.18 0.25 5.79 6.02 6.20 3.81 3.90 3.99 9.80 9.91 10.01 0.25 0.38 ...
Page 28
... MCP3204/3208 NOTES: DS21298C-page 28 2002 Microchip Technology Inc. ...
Page 29
... Microchip's development systems software products. Plus, this line provides information on how customers ® ® can receive the most current upgrade kits.The Hot Line or Microsoft Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-480-792-7302 for the rest of the world. MCP3204/3208 092002 DS21298C-page29 ...
Page 30
... Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y Device: MCP3204/3208 Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs you find the organization of this document easy to follow? If not, why? 4 ...
Page 31
... PART NO Device Grade Temperature Range Device: MCP3204: 4-Channel 12-Bit Serial A/D Converter MCP3204T: 4-Channel 12-Bit Serial A/D Converter (Tape and Reel) MCP3208: 8-Channel 12-Bit Serial A/D Converter MCP3208T: 8-Channel 12-Bit Serial A/D Converter (Tape and Reel) Grade ±1 LSB INL C = ±2 LSB INL ...
Page 32
... MCP3204/08 NOTES: DS21298C-page 32 2002 Microchip Technology Inc. ...
Page 33
... Serialized Quick Turn Programming (SQTP service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system ...
Page 34
... Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Microchip Technology (Barbados) Inc., Taiwan Branch 11F-3, No ...