LTC2240CUP-12#PBF Linear Technology, LTC2240CUP-12#PBF Datasheet - Page 15

• Manufacturer Part Number: LTC2240CUP-12#PBF
• Description: IC ADC 12BIT 170MSPS 64-QFN
• Manufacturer: Linear Technology

Specifications of LTC2240CUP-12#PBF

• Number Of Bits: 12
• Sampling Rate (per Second): 170M
• Data Interface: Parallel
• Number Of Converters: 1
• Power Dissipation (max): 638mW
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 64-WFQFN, Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATIONS INFORMATION
Each pipelined stage shown in Figure 1 contains an ADC,
a reconstruction DAC and an interstage residue amplifi er.
In operation, the ADC quantizes the input to the stage and
the quantized value is subtracted from the input by the
DAC to produce a residue. The residue is amplifi ed and
output by the residue amplifi er. Successive stages operate
out of phase so that when the odd stages are outputting
their residue, the even stages are acquiring that residue
and vice versa.
When ENC is low, the analog input is sampled differentially
directly onto the input sample-and-hold capacitors, inside
the “Input S/H” shown in the block diagram. At the instant
that ENC transitions from low to high, the sampled input is
held. While ENC is high, the held input voltage is buffered
by the S/H amplifi er which drives the fi rst pipelined ADC
stage. The fi rst stage acquires the output of the S/H dur-
ing this high phase of ENC. When ENC goes back low, the
fi rst stage produces its residue which is acquired by the
second stage. At the same time, the input S/H goes back
to acquiring the analog input. When ENC goes back high,
the second stage produces its residue which is acquired
by the third stage. An identical process is repeated for the
third and fourth stages, resulting in a fourth stage residue
that is sent to the fi fth stage ADC for fi nal evaluation.
Each ADC stage following the fi rst has additional range to
accommodate fl ash and amplifi er offset errors. Results
from all of the ADC stages are digitally synchronized such
that the results can be properly combined in the correction
logic before being sent to the output buffer.
SAMPLE/HOLD OPERATION AND INPUT DRIVE
Sample/Hold Operation
Figure 2 shows an equivalent circuit for the LTC2240-12
CMOS differential sample-and-hold. The analog inputs are
connected to the sampling capacitors (C
NMOS transistors. The capacitors shown attached to
each input (C
capacitance associated with each input.
During the sample phase when ENC is low, the transistors
connect the analog inputs to the sampling capacitors and
they charge to, and track the differential input voltage.
When ENC transitions from low to high, the sampled input
PARASITIC
) are the summation of all other
SAMPLE
) through
voltage is held on the sampling capacitors. During the
hold phase when ENC is high, the sampling capacitors are
disconnected from the input and the held voltage is passed
to the ADC core for processing. As ENC transitions from
high to low, the inputs are reconnected to the sampling
capacitors to acquire a new sample. Since the sampling
capacitors still hold the previous sample, a charging glitch
proportional to the change in voltage between samples will
be seen at this time. If the change between the last sample
and the new sample is small, the charging glitch seen at
the input will be small. If the input change is large, such
as the change seen with input frequencies near Nyquist,
then a larger charging glitch will be seen.
Common Mode Bias
For optimal performance the analog inputs should be driven
differentially. Each input should swing ±0.5V for the 2V
range or ±0.25V for the 1V range, around a common mode
voltage of 1.25V. The V
to provide the common mode bias level. V
directly to the center tap of a transformer to set the DC
input level or as a reference level to an op amp differential
driver circuit. The V
close to the ADC with a 2.2μF or greater capacitor.
ENC
ENC
A
A
IN
IN
+
–
+
–
LTC2240-12
10Ω
10Ω
1.5V
1.5V
6k
6k
V
V
DD
DD
Figure 2. Equivalent Input Circuit
V
DD
CM
CM
pin must be bypassed to ground
C
1.8pF
C
1.8pF
output pin (Pin 60) may be used
PARASITIC
PARASITIC
LTC2240-12
R
14Ω
R
14Ω
ON
ON
CM
C
C
SAMPLE
SAMPLE
2pF
2pF
can be tied
224012 F02
15
224012fc