3-644629-6 TE Connectivity, 3-644629-6 Datasheet - Page 6
![06P MTA156 HDR ASSY R/A LF](/photos/41/50/415017/pr8205651a_sml.jpg)
3-644629-6
Manufacturer Part Number
3-644629-6
Description
06P MTA156 HDR ASSY R/A LF
Manufacturer
TE Connectivity
Specifications of 3-644629-6
Connector Type
Header
Product Line
MTA-156
Pcb Mounting Orientation
Right Angle
Right Angle Bending Side
Front
Pcb Mount Retention
Without
Mating Connector Lock
With
Four Points Of Contact
Without
Shrouded
No
Mounting Ears
Without
Mating Connector Lock Type
Polarized Lock
Post Size (mm [in])
1.14 [.045]
Panel Mount Retention
Without
Current Rating (a)
7
Voltage Rating (vac)
600
Solder Tail Contact Plating
Tin
Termination Post Length (mm [in])
3.18 [0.125]
Number Of Positions
6
Centerline (mm [in])
3.96 [0.156]
Narrow
No
Post Number(s) Omitted
None
Contact Type
Pin
Contact Shape
Square
Contact Plating, Mating Area, Material
Gold (30) or (30) Total Gold Flash over Palladium Nickel
Contact Base Material
Copper Alloy
Connector Style
Plug
Housing Color
White
Mating Alignment
With
Ul Flammability Rating
UL 94V-0
Housing Material
Polyester
Backwall/post Interruption(s)
Without
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
Applies To
Printed Circuit Board
Application Use
Wire-to-Board
4.
4.1.
4.2.
4.3.
4.4.
Rev J
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets requirements of Figure 1. Failures attributed
to equipment, test setup or operator deficiencies shall not disqualify the product. If product failure
occurs, corrective action shall be taken and samples resubmitted for qualification. Testing to confirm
corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan will specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Sample Selection
Samples shall be prepared in accordance with applicable Instruction Sheets and shall be selected
at random from current production. Unless otherwise required for the test procedure, test groups 1,
2, 3 and 4 shall consist of mated pairs of MTA 156 connectors and headers. Test group 1 shall
consist of 5, 6 position standard tin plated samples; 5, 6 position high force tin plated samples; and
5, 6 position gold plated samples. All samples shall be terminated to the maximum wire size and
mounted on printed circuit board PN 93-660164. Test group 2 shall consist of 3, 10 position
standard tin plated samples terminated to 26 AWG wire and mounted on printed circuit board PN
93-660273-000; and 3, 10 position standard tin plated samples terminated to 18 AWG wire and
mounted on printed circuit board PN 93-660092-000. Test group 3 shall consist of 5 unmated and
unmounted 24 position standard tin plated samples terminated to maximum wire size. Test group
4 shall consist of 5, 10 position gold plated samples terminated to 22 AWG wire and mounted on
printed circuit board PN 93-660164. Test group 5 shall consist of 6, 10 position standard tin plated
samples terminated to minimum wire size; and 6, 10 position standard tin plated samples
terminated to maximum wire size. Test group 6 shall consist of 5, 6 position .156 tin plated
headers.
Test Sequence
Qualification inspection shall be verified by testing samples as specified in Figure 2.
108-1051
6 of 10