MAX191ACWG+ Maxim Integrated Products, MAX191ACWG+ Datasheet
![IC ADC 12BIT 100KSPS 24-SOIC](/photos/6/58/65845/406-175-24-soic_sml.jpg)
MAX191ACWG+
Specifications of MAX191ACWG+
Related parts for MAX191ACWG+
MAX191ACWG+ Summary of contents
Page 1
... AGND DGND SPI and QSPI are trademarks of Motorola, Inc. MICROWIRE is a trademark of National Semiconductor Corp. ________________________________________________________________ Maxim Integrated Products For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468. Low-Power, 12-Bit Sampling ADC ...
Page 2
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down ABSOLUTE MAXIMUM RATINGS V to DGND............................................................-0. AGND ............................................................-7V to +0. ..............................................................................12V DD SS AGND, VREF, REFADJ to DGND................-0. ...
Page 3
Internal Reference and Power-Down ELECTRICAL CHARACTERISTICS (continued ±5 -5V ±5 mode, reference compensation mode—external, synchronous operation, Figure 6, T PARAMETER SYMBOL ANALOG INPUT Input Voltage Range (Note 7) Input ...
Page 4
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down ELECTRICAL CHARACTERISTICS (continued ±5 -5V ±5 CLK mode, reference compensation mode—external, synchronous operation, Figure 6, T PARAMETER SYMBOL LOGIC OUTPUTS Output ...
Page 5
Internal Reference and Power-Down TIMING CHARACTERISTICS (Figures 6–10) (continued) (V =5V ±5 -5V ±5 PARAMETER SYMBOL Hold Time Setup Time ...
Page 6
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down __________________________________________Typical Operating Characteristics CLOCK FREQUENCY vs. TIMING CAPACITOR 10 SEE FIGURE +25˚ 0.1 0.01 0 TIMING CAPACITOR (nF) POSITIVE SUPPLY CURRENT vs. TEMPERATURE 3.5 ...
Page 7
Internal Reference and Power-Down PIN NAME Power-Down Input. A logic low at PD deactivates the ADC—only the bandgap reference is active. A logic PD 1 high selects normal operation, internal-reference compensation mode. An open-circuit condition selects normal operation, external-reference ...
Page 8
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down DGND a. High and High Figure 1. Load Circuits for Access Time DN 10pF 3k DGND ...
Page 9
Internal Reference and Power-Down AIN + TRACK C HOLD HOLD 32pF SWITCH PACKAGE 10pF 5pF HOLD AIN - 12-BIT DAC Figure 4. Equivalent Input Circuit various interface modes. The time required for the T/H to acquire ...
Page 10
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down CLK BUSY t 2 CS, RD, and CLK Synchronous Operation Figure 6. between 45% and 55%. Clock and Control Synchronization For best ...
Page 11
Internal Reference and Power-Down HBEN CONV 2 BUSY t 3 OLD DATA DATA D7– HOLD* TRACK *INTERNAL SIGNAL. TRACKING INPUT SIGNAL WHEN HOLD = Low, HOLDING WHEN HOLD = ...
Page 12
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down HBEN t 8 CLK BUSY t 3 OLD DATA DATA D7– HOLD* TRACK *INTERNAL SIGNAL. TRACKING INPUT SIGNAL WHEN HOLD = ...
Page 13
Internal Reference and Power-Down Table 1. Data-Bus Output, PIN NAME D7/DOUT HBEN = 0, PAR = 1, D7 PARALLEL MODE HBEN = 1, PAR = 1, Low PARALLEL MODE HBEN = X, PAR = 0, DOUT SERIAL MODE, RD ...
Page 14
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down 23 SCLK DOUT RD MAX191 SCLK OUT HBEN SSTRB LOGIC INPUT CS SCLK SCLK OUT DOUT SSTRB NOTE: USE SSTRB TO GATE PARALLEL DATA TRANSFER FROM SHIFT REGISTER, ...
Page 15
Internal Reference and Power-Down ing edge of the first clock cycle after conversion end (when BUSY goes high). As mentioned previously, two more read operations (after BUSY goes high) are needed to access the conversion results. The only dif- ...
Page 16
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down f (MAX) = (1/ SCLK where t (M) is the minimum data-setup time re- su quired at the serial data input to the µP. For example, Motorola’s ...
Page 17
Internal Reference and Power-Down SCLK CS HIGH-Z DOUT MSB a. CPOL = 0, CPHA = 0 SCLK CS HIGH-Z DOUT MSB D10 b. CPOL = 1, CPHA = 1 Figure 15. QSPI Serial-Interface Timing SCLK CLKR CS HIGH-Z SSTRB ...
Page 18
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down Following the data transfer, the DSP receive shift regis- ter (RSR) contains a 16-bit word consisting of the 12 data bits, MSB first, followed by four trailing 0s. Applications Information Power-On ...
Page 19
Internal Reference and Power-Down VREF Figure 18b. Low Average-Power Mode Operation (Internal Compensation) which can be achieved using power-down between conversions. External Compensation Figure 19a shows the connection for ...
Page 20
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down OPEN CIRCUIT (FLOAT VREF 2ms 200ms 12 Figure 19b. Low Average-Power Mode Operation (External Compensation) between FFE (hex) and FFF (hex). Because interaction occurs between adjustments, offset ...
Page 21
Internal Reference and Power-Down R7 10k MAX480 10k R1 10k R2 100 VREF R3 R5 10k 10k R6 10k R4 49.9 VREF R9* 20k R10* 0.1 F* 49.9 * CONNECT AIN- TO AGND WHEN USING DUAL ...
Page 22
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down 0.01µF and 10µF bypass capacitors. Minimize capaci- tor lead lengths for best supply-noise rejection. If the +5V power supply is very noisy, a 10Ω resistor can be connected as a lowpass ...
Page 23
Internal Reference and Power-Down TTL/CMOS IC OUTPUTS 1 MAX250 SHDN 4 3 TTL/CMOS INPUTS GND 8 7 Figure 24. Isolated Data-Acquisition Circuit ______________________________________________________________________________________ Low-Power, ...
Page 24
Low-Power, 12-Bit Sampling ADC with Internal Reference and Power-Down ___________________Chip Topography VREF REFADJ AGND BIP 0.142" (3.6065mm) SUBSTRATE CONNECTED ________________________________________________________Package Information 24 ______________________________________________________________________________________ HBEN CS RD 0.198" (5.0292mm) D7/DOUT D6/SCLK OUT ...