4-173977-9 TE Connectivity, 4-173977-9 Datasheet
4-173977-9
Specifications of 4-173977-9
Available stocks
Related parts for 4-173977-9
4-173977-9 Summary of contents
Page 1
... LTR REVISION RECORD ASHL-0004-ES REV A Product Specification 108-5218 2mm Pitch, M/T Type M/T Receptacle Connector Assembly, 2-15-Pos. #28/#26 AWG M/T Receptacle Connector Assembly, 2-15-Pos. #24 AWG Fig. 1 Test Specification, General Requirements for Test Methods Application Specification Test Report DR T. FURUYA 4/12’91 CHK S ...
Page 2
... Nylon (UL94 V-0) : Brass (0.2um min. thick Au Plated over 1~2um thick Nickel underplate) : 6/6 Nylon GF Type (UL94 V-0) : Pretin lead Brass (0.8um min. thick solder-plated over 0.5um min. thick copper underplate (UL 94V-0) : Pretin lead Brass (0.8um min. thick solder-plated over 0.5um min. ...
Page 3
... AWG 1A #28 AWG +105 C The upper limit of the temperature includes the temperature rising resulted by the energised electrical current. : #28 AWG, #26 AWG (0.08~0.14mm Recommended UL Grade: UL 1061, UL 1571 2 #24 AWG (0.22mm ) Recommended UL Grade: UL 1728 : 0.83~1.05mm 0.95~1.05mm (Only AWG #24) : 0.8~1.6mm : 0.8~0.9mm (for punched holes) ...
Page 4
... Fig. 2 (To be continued) PAGE Document No Procedures Subject terminated connector and header to mate and unmate to measure the force required to engage and disengage by operating the head at a rate minute. Record by using autograph. Lock Side. 7.84 9.80 12.74 16 ...
Page 5
... Wire Size Direction Direction (AWG) [Min.] [Min.] Unit: N Unit 7 & #24 7.8 14.7N Min. per contact. Fig. 2 (To be continued) PAGE Document No Procedures After preconditioning by using applicable post for 3 cycles, measure the force required to unmate post by operating the head at a rate of 50mm a minute. ...
Page 6
... ASHL-0005- ES REV B Requirements 49.0N Max. 83.3N Min. Product shall be confirming to the requirements of applicable product drawing and Application Specification 114-5104. Electrical Performance Requirements 10 m Max. (Initial Max. (Final) Connector must withstand test potential of 1.0 kV (AC) for 1 minute. Current leakage must be 5.0mA Max. ...
Page 7
... C and 90~95 % R.H. MIL-STD-202, Method 103, Condition B. Subject mated connectors cycles between -55 C and 85 C for 30 minutes each duration at temperature extremes. MIL-STD-202, Method 107, Condition A. Subject mated/unmated connectors to 5% salt concentration for 48 hours. MIL-STD-202, Method 101, Condition B. REV LOC 108-5218 S ES ...
Page 8
... PAGE Document No Procedures Subject mated connectors to sulfurous acid gas atmosphere of 3±1ppm concentration at o 40±2 C for 240 hours. Subsequent measurement shall be done after reconditioning in the room temperature for 1 hour. Subject contacts to solderability testing, as specified. MIL-STD-202, Method 208. Subject product mounted on printed circuit boards to solder o bath at 260± ...
Page 9
... Fig.5 Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig.3 Fig.4 Fig.6 Fig.7 PAGE Document No 108-5218 REV LOC S ES ...
Page 10
... Test Specimens: The test specimens to be used for the performance evaluation testing, shall be prepared in accordance with AMP Application Specification, 114-5104, Termination of AMP CT Connector Pitch, M/T Type, by using the samples selected from the current production at random, and conforming to the requirements of the applicable product drawing. ...
Page 11
... Post Header, Vertical (V), Short Tine, Box Type X-175489-X Post Header, Horizontal (H), Box Type X-175661-X Post Header, Horizontal (H), Box Type, in Tube X-176394-X Post Header, Horizontal (H), Gold-plated Contact, Box Type X-177626-X Post Header, Horizontal (H), Short Tine, Box Type X-175694-X Post Header, w/Panel Lock, for Relay Tyco Electronics AMP Shanghai Ltd ...
Page 12
... Pos. 6 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 3 Pos. 3 Pos. 2~6, 8 Pos. 2~6, 8 Pos. 2~5 Pos. 2~5 Pos. 2~6, 8 Pos 8~11 Pos. 3 Pos. 7~10, 13 Pos. 2~8 Pos. 2~8 Pos. 2 Pos. 3 Pos. 3 Pos. 2~8 Pos. 2~8 Pos. REV LOC S ...