LTC1405IGN Linear Technology, LTC1405IGN Datasheet - Page 13

• Manufacturer Part Number: LTC1405IGN
• Description: IC ADC 12BIT 5MSPS SAMPLE 28SSOP
• Manufacturer: Linear Technology

Specifications of LTC1405IGN

• Number Of Bits: 12
• Sampling Rate (per Second): 5M
• Data Interface: Parallel
• Number Of Converters: 1
• Power Dissipation (max): 145mW
• Voltage Supply Source: Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP (0.150", 3.95mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIO S I FOR ATIO
Digital Outputs and Overflow Bit (OF)
Figure 10 shows the ideal input/output characteristics for
the LTC1405. The output data is two’s complement binary
for all input ranges and for both single and dual supply
operation. One LSB = V
binary output, invert the MSB (D11). The overflow bit (OF)
indicates when the analog input is outside the input range
of the converter. OF is high when the output code is 1000
0000 0000 or 0111 1111 1111.
Full-Scale and Offset Adjustment
In applications where absolute accuracy is important,
offset and full-scale errors can be adjusted to zero. Offset
error should be adjusted before full-scale error. Figure 11
shows a method for error adjustment for a dual supply,
4.096V application. For zero offset error apply – 0.5mV
(i. e., – 0.5LSB) at + A
flickers between 0000 0000 0000 and 1111 1111 1111.
For full-scale adjustment, apply an input voltage of 2.0465V
(FS – 1.5LSBs) at + A
flickers between 0111 1111 1110 and 0111 1111 1111.
Digital Output Drivers
The LTC1405 output drivers can interface to logic operat-
ing from 3V to 5V by setting OV
supply. If 5V output is desired, OV
and share its decoupling capacitor. Otherwise, OV
quires its own 1µF decoupling capacitor. To prevent digital
011…111
011…110
011…101
100…010
100…001
100…000
Figure 10. LTC1405 Transfer Characteristics
–(FS – 1LSB)
U
IN
IN
INPUT VOLTAGE (V)
and adjust R2 until the output code
and adjust R1 until the output code
REF
U
/4.096. To create a straight
DD
DD
W
can be shorted to V
FS – 1LSB
to the logic power
1405 F10
1
0
OVERFLOW
BIT
U
DD
re-
DD
noise from affecting performance, the load capacitance on
the digital outputs should be minimized. If large capacitive
loads are required, (>30pF) external buffers or 100Ω
resistors in series with the digital outputs are suggested.
Timing
The conversion start is controlled by the rising edge of the
CLK pin. Once a conversion is started it cannot be stopped
or restarted until the conversion cycle is complete. Output
data is updated at the end of conversion, or about 150ns
after a conversion is begun. There is an additional two
cycle pipeline delay, so the data for a given conversion is
output two full clock cycles plus 150ns after the convert
start. Thus output data can be latched on the third CLK
rising edge after the rising edge that samples the input.
Clock Input
The LTC1405 only uses the rising edge of the CLK pin for
internal timing, and CLK doesn’t necessarily need to have
a 50% duty cycle. For optimal AC performance the rise
time of the CLK should be less than 5ns. If the available
clock has a rise time slower than 5ns, it can be locally sped
up with a logic gate. With single supply operation the clock
can be driven with 5V CMOS, 3V CMOS or TTL logic levels.
With dual power supplies the clock should be driven with
5V CMOS levels.
As with all fast ADCs, the noise performance of the
LTC1405 is sensitive to clock jitter when high speed inputs
Figure 11. Offset and Full-Scale Adjust Circuit
1µF
50k
R1
–5V
5V
10k
10k
R2
1k
24k
100Ω
V
IN
+A
–A
V
SENSE
REF
IN
IN
LTC1405
V
–5V
5V
SS
1405 F11
LTC1405
13
1405fa