406372-4 TE Connectivity, 406372-4 Datasheet - Page 2

• Manufacturer Part Number: 406372-4
• Description: 110 MJ ASSY,RJ45,UNIV,CAT5
• Manufacturer: TE Connectivity
• Series: 110Connectr

Specifications of 406372-4

• Product: Telecom & Ethernet Connectors
• Performance Category: Cat 5e
• Usoc Codes: RJ45
• Number Of Ports: 1
• Gender: Female
• Shielding: Unshielded
• Contact Plating: Gold
• Housing Material: Polyphenylene Oxide
• Color: Gray
• Product Type: Connector - Modular
• Jack Type: RJ45
• Wiring Pattern: Universal
• Termination Style: 110 Style Punch-Down
• Keyed: No
• Stuffer Cap Material: Polyphenylene Oxide
• Stuffer Cap Color: Gray
• Shielded: No
• Solder Tail Contact Plating: Tin-Lead over Nickel
• Number Of Positions: 8
• Netconnect Select System: Yes
• Conductor O.d. (mm [in]): 1.27 [0.050]
• Mount Type: Panel Mount
• Wire Range (solid) (mm [awg]): 22-26
• Wire Range (stranded) (mm² [awg]): 22-26
• 110 Block Material: Polycarbonate
• Contact Base Material: Phosphor Bronze
• Contact Plating, Mating Area, Material: Gold
• Contact Plating, Mating Area, Thickness (µm [?in]): 1.27 [50]
• Housing Color: NEMA Gray
• Ul Flammability Rating: UL 94V-0
• Dust Cover: Without
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C
• Rohs/elv Compliance History: Converted to comply with RoHS directive
• Packaging Method: Poly Bag
• Packaging Quantity: 1
• Lead Free Status / Rohs Status: In Transition

3.2.
3.3.
3.4.
3.5.
Rev B
Examination of product.
Termination resistance, specified
current.
Termination resistance, dry circuit.
Materials
!
!
!
Ratings
!
!
!
!
!
!
Performance and Test Description
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure 1. All tests shall be performed at ambient environmental conditions per Test
Specification 109-1 unless otherwise specified.
Test Requirements and Procedures Summary
Test Description
Housings:
•
•
Terminals:
•
•
Shield: Brass, tin-lead plating
Voltage: 150 volts alternating current
Current: 1.5 amperes maximum (signal application only)
Temperature: -40 to 70° C
Shielding effectiveness: Shielding effectiveness is measured by comparing level of
electromagnetic emissions from an unshielded system with that of a shielded system. A system
includes active electronic devices and associated cables. Emission levels can be affected by many
variables such as cable type, cable length, grounding method and test setup. Contribution of a
shielded connector to overall shielding will vary with each application. Typically, a shielded modular
plug/jack interface may be expected to improve shielding effectiveness approximately 20 dB as
compared to an unshielded interface.
Frequency range:
•
•
Characteristic impedance: 100 ohms
Modular jack: Polyphenylene oxide, UL94V-0
Connector block: Polycarbonate, UL94V-0
Modular jack: Phosphor bronze, gold over nickel plating
Connector block: Phosphor bronze, tin-lead over nickel plating
Category 3: 1 - 16 MHz
Category 5: 1 - 100 MHz
Meets requirements of product
drawing.
24 AWG wire size;
1 ampere test current;
100 milliohms resistance.
100 milliohms maximum initial.
120 milliohms maximum final.
Figure 1 (continued)
ELECTRICAL
Requirement
Visual, dimensional and functional
per applicable quality inspection
plan.
TE Spec 109-25.
Measure potential drop of jack and
mated plug assembly.
Calculate resistance.
See Figure 3.
TE Spec 109-6-1.
Subject jack and mated plug
assembly to 50 mv open circuit at
100 ma.
See Figure 3.
Procedure
108-1389
2 of 6