LTC2233IUK#PBF Linear Technology, LTC2233IUK#PBF Datasheet - Page 20
![IC ADC 10BIT 80MSPS SAMPLE 48QFN](/photos/6/62/66222/48-qfn_05-08-1704_sml.jpg)
LTC2233IUK#PBF
Manufacturer Part Number
LTC2233IUK#PBF
Description
IC ADC 10BIT 80MSPS SAMPLE 48QFN
Manufacturer
Linear Technology
Datasheet
1.LTC2232IUKPBF.pdf
(28 pages)
Specifications of LTC2233IUK#PBF
Number Of Bits
10
Sampling Rate (per Second)
80M
Data Interface
Parallel
Number Of Converters
1
Power Dissipation (max)
406mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-WFQFN, Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
LTC2232/LTC2233
APPLICATIO S I FOR ATIO
Input Range
The input range can be set based on the application. The
2V input range will provide the best signal-to-noise perfor-
mance while maintaining excellent SFDR. The 1V input
range will have better SFDR performance, but the SNR will
degrade by 1.5dB. See the Typical Performance Charac-
teristics section.
Driving the Encode Inputs
The noise performance of the LTC2232/LTC2233 can
depend on the encode signal quality as much as on the
analog input. The ENC
driven differentially, primarily for noise immunity from
common mode noise sources. Each input is biased through
a 6k resistor to a 1.6V bias. The bias resistors set the DC
operating point for transformer coupled drive circuits and
can set the logic threshold for single-ended drive circuits.
Any noise present on the encode signal will result in
additional aperture jitter that will be RMS summed with the
inherent ADC aperture jitter.
20
CLOCK
INPUT
0.1µF
50Ω
Figure 11. Transformer Driven ENC
1:4
ENC –
ENC
+
U
LTC2232/LTC2233
V
V
DD
DD
+
/ENC
U
1.6V BIAS
1.6V BIAS
–
6k
6k
inputs are intended to be
V
W
DD
+
/ENC
ADC CIRCUITS
U
TO INTERNAL
–
22323 F11
In applications where jitter is critical (high input frequen-
cies) take the following into consideration:
1. Differential drive should be used.
2. Use as large an amplitude as possible; if transformer
coupled use a higher turns ratio to increase the amplitude.
3. If the ADC is clocked with a sinusoidal signal, filter the
encode signal to reduce wideband noise.
4. Balance the capacitance and series resistance at both
encode inputs so that any coupled noise will appear at both
inputs as common mode noise. The encode inputs have a
common mode range of 1.1V to 2.5V. Each input may be
driven from ground to V
Maximum and Minimum Encode Rates
The maximum encode rate for the LTC2232/LTC2233 is
105Msps (LTC2232) and 80Msps (LTC2233). For the ADC
to operate properly, the encode signal should have a 50%
(±5%) duty cycle. Each half cycle must have at least 4.5ns
(LTC2232) or 5.9ns (LTC2233) for the ADC internal cir-
cuitry to have enough settling time for proper operation.
Achieving a precise 50% duty cycle is easy with differential
sinusoidal drive using a transformer or using symmetric
differential logic such as PECL or LVDS.
An optional clock duty cycle stabilizer circuit can be used
if the input clock has a non 50% duty cycle. This circuit
uses the rising edge of the ENC
input. The falling edge of ENC
falling edge is generated by a phase-locked loop. The input
clock duty cycle can vary from 20% to 80% and the clock
duty cycle stabilizer will maintain a constant 50% internal
duty cycle. If the clock is turned off for a long period of
time, the duty cycle stabilizer circuit will require a hundred
clock cycles for the PLL to lock onto the input clock. To use
the clock duty cycle stabilizer, the MODE pin should be
connected to 1/3V
DD
or 2/3V
DD
for single-ended drive.
DD
+
is ignored and the internal
+
using external resistors.
pin to sample the analog
22323fa