5-6610090-6 TE Connectivity, 5-6610090-6 Datasheet - Page 3
![1X6 MAG45 7G1P1, 01, G/Y & G/Y](/photos/41/71/417133/pr6610085_sml.jpg)
5-6610090-6
Manufacturer Part Number
5-6610090-6
Description
1X6 MAG45 7G1P1, 01, G/Y & G/Y
Manufacturer
TE Connectivity
Specifications of 5-6610090-6
Product Type
Connector
Number Of Cores
8
Magnetics
Integrated Magnetics
Jack Type
RJ45
Signal Routing Type
Auto MDI/MDIX
Profile
Standard
Pcb Mounting Orientation
Side Entry (Right Angle)
Jack Configuration
1 x 6
Turns Ratio
1:1
Shielded
Yes
Emi Finger - Bottom
With
Termination Method
Solder
Port Configuration
Multiple
Emi Fingers -top And Sides
Without
Latch Orientation
Inverted - Latch Up
Pcb Tail Length (mm [in])
3.68 [0.145]
Contact Termination Type
Through Hole
Preloaded
Yes
Connector Style
Jack
Status Indicator
LED
Decoupling Capacitor
2KV
Rear Pcb Ground Tab
Without
Signal Lead Quantity
10
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
Left Led Color (position #1)
Green/Yellow (Bicolor)
Right Led Color (position #2)
Green/Yellow (Bicolor)
Operating Temperature (°c [°f])
0 – 70 [32 – 158]
Applies To
Printed Circuit Board
Environmental Conditions
Office / Premises
Application
Gigabit Ethernet
Durability, 500 cycles.
Durability, 2000 cycles.
Mating force.
Unmating force.
Normal force.
Modular plug retention to modular
jack.
Thermal shock.
Humidity-temperature cycling.
Mixed flowing gas.
Extended temperature.
Rev D
Test Description
See Note.
See Note.
20.02 N [4.5 lbf] maximum.
See Note.
20.02 N [4.5 lbf] maximum.
See Note.
100 gram force [3.53 ozf] minimum
per FCC Part 68, Subpart F
Connector Requirements.
57.83 N [13 lbf] minimum.
Plug shall not disengage from jack.
See Note.
See Note.
See Note.
No discontinuities of 1
microsecond or longer duration at
temperature levels.
See Note.
Figure 1 (continued)
ENVIRONMENTAL
Requirement
EIA-364-9C.
Manually mate and unmate
specimens with the plug locking
tab inoperable for 500 cycles at a
maximum rate of 300 cycles per
hour.
EIA-364-9C.
Manually mate and unmate
specimens with the plug locking
tab inoperable for 2000 cycles at a
maximum rate of 300 cycles per
hour.
EIA-364-13B.
Measure force necessary to mate
specimens at a maximum rate of
12.7 mm [.5 in] per minute.
EIA-364-13B.
Measure force necessary to
unmate specimens at a maximum
rate of 12.7 mm [.5 in] per minute.
EIA-364-4.
Measure and record normal force
generated at any given deflection
level within the normal operating
range with an FCC compliant
modular plug.
EIA-364-98.
Subject mounted specimens to
specified force applied for 1 minute
in 4 directions with plug mated in
jack and latch engaged.
EIA-364-32C.
Subject mated and mounted
specimens to 5 cycles between -25
+0/-3 and 70 +3/-0° C with 60
minute dwell at temperature
extremes.
EIA-364-31B,
Method IV.
Subject mated and mounted
specimens to 10 cycles (10 days)
between 25 and 65° C at 90 to 95%
RH.
EIA-364-65,
Class IIA (4 gas).
Subject mated and unmated
specimens to environmental Class
IIA for 10 days.
Subject mated and mounted
specimens to 2 hours at each of
the following temperatures: -5, 25,
55 and 75 ± 2° C.
Procedure
108-2100
3 of 6