AD7466BRTZ-R2 Analog Devices Inc, AD7466BRTZ-R2 Datasheet - Page 23

• Manufacturer Part Number: AD7466BRTZ-R2
• Description: IC ADC 12BIT 1.6V LP SOT23-6
• Manufacturer: Analog Devices Inc

Specifications of AD7466BRTZ-R2

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Design Resources: Software Calibrated, 50 MHz to 9 GHz, RF Power Measurement System (CN0178)
• Number Of Bits: 12
• Sampling Rate (per Second): 200k
• Number Of Converters: 1
• Power Dissipation (max): 900µW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-6
• Resolution (bits): 12bit
• Sampling Rate: 200kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: 1.6V To 3.6V
• Supply Current: 300µA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7466CBZ - BOARD EVALUATION FOR AD7466
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

MICROPROCESSOR INTERFACING
The serial interface on the AD7466/AD7467/AD7468 allows
the parts to be connected directly to many different micro-
processors. This section explains how to interface the AD7466/
AD7467/AD7468 with some of the more common microcontroller
and DSP serial interface protocols.
AD7466/AD7467/AD7468 to TMS320C541 Interface
The serial interface on the TMS320C541 uses a continuous
serial clock and frame synchronization signals to synchronize
the data transfer operations with peripheral devices like the
AD7466/AD7467/AD7468. The CS input allows easy inter-
facing between the TMS320C541 and the AD74xx devices,
without requiring any glue logic. The serial port of the
TMS320C541 is set up to operate in burst mode (FSM = 1
in the serial port control register, SPC) with internal CLKX
(MCM = 1 in the SPC register) and internal frame signal
(TXM = 1 in the SPC register), so both pins are configured as
outputs. For the AD7466, the word length should be set to
16 bits (FO = 0 in the SPC register). The standard synchronous
serial port interface in this DSP allows only frames with a word
length of 16 bits or 8 bits. Therefore, for the AD7467 and
AD7468 where 14 and 12 bits are required, the FO bit also
would be set up to 16 bits. In these cases, the user should keep
in mind that the last 2 bits and 4 bits for the AD7467 and
AD7468, respectively, are invalid data as the SDATA line goes
back into three-state on the 14th and 12th SCLK falling edge.
To summarize, the values in the SPC register are FO = 0,
FSM = 1, MCM = 1, and TXM = 1.
SDATA
SCLK
CS
THREE-STATE
t
2
0
1
t
3
0
4 LEADING ZEROS
2
0
B
Figure 31. AD7468 Serial Interface Timing Diagram
3
0
4
t
CONVERT
Rev. C | Page 23 of 28
DB7
t
4
t
6
t
5
8 BITS OF DATA
t
7
Figure 32 shows the connection diagram. For signal processing
applications, it is imperative that the frame synchronization
signal from the TMS320C541 provide equidistant sampling.
AD7466/AD7467/AD7468 to ADSP-218x Interface
The ADSP-218x family of DSPs is interfaced directly to the
AD7466/AD7467/AD7468 without any glue logic. The SPORT
control register must be set up as described in Table 9.
Table 9. SPORT Control Register Setup
Setting
TFSW = RFSW = 1
INVRFS = INVTFS = 1
DTYPE = 00
ISCLK = 1
TFSR = RFSR = 1
IRFS = 0
ITFS = 1
SLEN = 1111
SLEN = 1101
SLEN = 1011
11
DB0
1
ADDITIONAL PINS OMITTED FOR CLARITY.
t
AD7468
AD7466/
AD7467/
8
12
Figure 32. Interfacing to the TMS320C541
SDATA
1
SCLK
CS
AD7466/AD7467/AD7468
THREE-STATE
t
QUIET
Description
Alternate framing
Active low frame signal
Right-justify data
Internal serial clock
Frame every word
Sets up RFS as an input
Sets up TFS as an output
16 bits for the AD7466
14 bits for the AD7467
12 bits for the AD7468
t
1
CLKX
CLKR
DR
FSX
FSR
TMS320C541
1