MAX1185ECM/V+T Maxim Integrated Products, MAX1185ECM/V+T Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1185ECM/V+T
Manufacturer Part Number
MAX1185ECM/V+T
Description
IC ADC 10BIT 20MSPS DL LP 48TQFP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1185ECMD.pdf
(21 pages)
Specifications of MAX1185ECM/V+T
Number Of Bits
10
Sampling Rate (per Second)
20M
Number Of Converters
2
Power Dissipation (max)
2.43W
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-TQFP Exposed Pad, 48-eTQFP, 48-HTQFP, 48-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Dual 10-Bit, 20Msps, 3V, Low-Power ADC with
Internal Reference and Multiplexed Parallel Outputs
The full-scale range of the MAX1185 is determined by the
internally generated voltage difference between REFP
(V
The full-scale range for both on-chip ADCs is adjustable
through the REFIN pin, which is provided for this purpose.
REFOUT, REFP, COM (V
buffered low-impedance outputs.
The MAX1185 provides three modes of reference operation:
In internal reference mode, connect the internal refer-
ence output REFOUT to REFIN through a resistor (e.g.,
10kΩ) or resistor-divider, if an application requires a
reduced full-scale range. For stability and noise filtering
purposes, bypass REFIN with a > 10nF capacitor to
GND. In internal reference mode, REFOUT, COM, REFP,
and REFN become low-impedance outputs.
In buffered external reference mode, adjust the reference
voltage levels externally by applying a stable and accu-
rate voltage at REFIN. In this mode, COM, REFP, and
REFN become outputs. REFOUT may be left open or con-
nected to REFIN through a > 10kΩ resistor.
In unbuffered external reference mode, connect REFIN to
GND. This deactivates the on-chip reference buffers for
REFP, COM, and REFN. With their buffers shut down,
these nodes become high impedance and may be driven
through separate, external reference sources.
The MAX1185’s CLK input accepts CMOS-compatible
clock signals. Since the interstage conversion of the
device depends on the repeatability of the rising and
falling edges of the external clock, use a clock with low jit-
ter and fast rise and fall times (< 2ns). In particular, sam-
pling occurs on the rising edge of the clock signal,
requiring this edge to provide lowest possible jitter. Any
significant aperture jitter would limit the SNR performance
of the on-chip ADCs as follows:
where f
is the time of the aperture jitter.
Clock jitter is especially critical for undersampling appli-
cations. The clock input should always be considered as
an analog input and routed away from any analog input
or other digital signal lines.
12
DD
• Internal reference mode
• Buffered external reference mode
• Unbuffered external reference mode
______________________________________________________________________________________
/ 2 + V
IN
SNR
represents the analog input frequency and t
REFIN
dB
= 20 x log
/ 4) and REFN (V
Analog Inputs and Reference
DD
10
/ 2), and REFN are internally
(1 / [2π x f
Clock Input (CLK)
DD
Configurations
IN
/ 2 - V
x t
AJ
])
REFIN
/ 4).
AJ
The MAX1185 clock input operates with a voltage thresh-
old set to V
than 50%, must meet the specifications for high and low
periods as stated in the Electrical Characteristics .
Figure 3 shows the relationship between clock and
analog input, A/B indicator, and the resulting CHA/CHB
data output. CHA and CHB data are sampled on the
rising edge of the clock signal. Following the rising
edge of the 5th clock cycles, the digitized value of the
original CHA sample is presented at the output, fol-
lowed one half-clock cycle later by the digitized value
of the original CHB sample.
A channel selection signal (A/B indicator) allows the user
to determine which output data represents which input
channel. With A/B = 1, digitized data from CHA is present
at the output and with A/B = 0 digitized data from CHB is
present.
All digital outputs, D0A/B–D9A/B (CHA or CHB data) and
A/B are TTL/CMOS logic-compatible. The output coding
can be chosen to be either offset binary or two’s comple-
ment (Table 1) controlled by a single pin (T/B). Pull T/B
low to select offset binary and high to activate two’s com-
plement output coding. The capacitive load on the digital
outputs D0A/B–D9A/B should be kept as low as possible
(< 15pF), to avoid large digital currents that could feed
back into the analog portion of the MAX1185, thereby
degrading its dynamic performance. Using buffers on
the digital outputs of the ADCs can further isolate the
digital outputs from heavy capacitive loads. To further
improve the dynamic performance of the MAX1185,
small-series resistors (e.g., 100Ω) may be added to the
digital output paths close to the MAX1185.
Figure 4 displays the timing relationship between output
enable and data output valid as well as power-
down/wake-up and data output valid.
The MAX1185 offers two power-save modes—sleep
and full power-down mode. In sleep mode (SLEEP = 1),
only the reference bias circuit is active (both ADCs are
disabled), and current consumption is reduced to
2.8mA.
To enter full power-down mode, pull PD high. With OE
simultaneously low, all outputs are latched at the last
value prior to the power-down. Pulling OE high forces
the digital outputs into a high-impedance state.
Selection (T/B), Output Enable ( OE ), Channel
Digital Output Data, Output Data Format
DD
/2. Clock inputs with a duty cycle other
System Timing Requirements
Power-Down (PD) and Sleep
(SLEEP) Modes
Selection (A/B)