LTC1290BISW Linear Technology, LTC1290BISW Datasheet - Page 21
![IC DATA ACQ SYS 12BIT 20-SOIC](/photos/6/63/66331/20-soic_05-08-1620_sml.jpg)
LTC1290BISW
Manufacturer Part Number
LTC1290BISW
Description
IC DATA ACQ SYS 12BIT 20-SOIC
Manufacturer
Linear Technology
Type
Data Acquisition System (DAS), ADCr
Datasheet
1.LTC1290CCSWPBF.pdf
(32 pages)
Specifications of LTC1290BISW
Resolution (bits)
12 b
Sampling Rate (per Second)
50k
Data Interface
Serial, Parallel
Voltage Supply Source
Dual ±
Voltage - Supply
±5V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC1290BISW#PBF
Manufacturer:
LT
Quantity:
4
Part Number:
LTC1290BISW#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
maximum clock rates (ACLK = 4MHz and SCLK = 2MHz).
Figures 11 and 12 show examples of adequate and poor
op amp settling.
RC Input Filtering
It is possible to filter the inputs with an RC network as shown
in Figure 13. For large values of C
input switching currents are averaged into a net DC current.
Therefore, a filter should be chosen with a small resistor and
large capacitor to prevent DC drops across the resistor. The
magnitude of the DC current is approximately I
(100pF)(V
running at the minimum cycle time of 20µs, the input
current equals 25µA at V
of 5Ω will cause 0.1LSB of full-scale error. If a larger filter
resistor must be used, errors can be eliminated by increas-
ing the cycle time as shown in the typical curve of Maximum
Filter Resistor vs Cycle Time.
A
Figure 11. Adequate Settling of Op Amps Driving Analog Input
PPLICATI
Figure 12. Poor Op Amp Settling Can Cause A/D Errors
IN
/t
CYC
) and is roughly proportional to V
O
U
HORIZONTAL: 500ns/DIV
HORIZONTAL: 20µs/DIV
S
IN
= 5V. In this case, a filter resistor
I FOR ATIO
U
F
(e.g., 1µF), the capacitive
W
IN
U
. When
DC
=
Input Leakage Current
Input leakage currents can also create errors if the source
resistance gets too large. For instance, the maximum input
leakage specification of 1µA (at 125°C) flowing through a
source resistance of 1kΩ will cause a voltage drop of 1mV
or 0.8LSB. This error will be much reduced at lower
temperatures because leakage drops rapidly (see the
typical curve of Input Channel Leakage Current vs Tem-
perature).
Noise Coupling Into Inputs
High source resistance input signals (>500Ω) are more
sensitive to coupling from external sources. It is prefer-
able to use channels near the center of the package (i.e.,
CH2 to CH7) for signals which have the highest output
resistance because they are essentially shielded by the
pins on the package ends (DGND and CH0). Grounding
any unused inputs (especially the end pin, CH0) will also
reduce outside coupling into high source resistances.
4. Sample-and-Hold
Single-Ended Inputs
The LTC1290 provides a built-in sample-and-hold (S&H)
function for all signals acquired in the single-ended mode
(COM pin grounded). This sample-and-hold allows the
LTC1290 to convert rapidly varying signals (see the typical
curve of S&H Acquisition Time vs Source Resistance). The
input voltage is sampled during the t
Figure 10. The sampling interval begins after the fourth MUX
address bit is shifted in and continues during the remainder
of the data transfer. On the falling edge of the final SCLK, the
S&H goes into hold mode and the conversion begins. The
voltage will be held on either the 8th, 12th or 16th falling edge
of the SCLK depending on the word length selected.
V
IN
R
FILTER
Figure 13. RC Input Filtering
I
DC
C
FILTER
"+"
"–"
LTC1290
SMPL
LTC1290 F13
time as shown in
LTC1290
21
1290fe