MAX5423ETA+T Maxim Integrated Products, MAX5423ETA+T Datasheet - Page 7

• Manufacturer Part Number: MAX5423ETA+T
• Description: IC POT DGTL 256-TAP NV 8-TDFN
• Manufacturer: Maxim Integrated Products

Specifications of MAX5423ETA+T

• Taps: 256
• Resistance (ohms): 100K
• Number Of Circuits: 1
• Temperature Coefficient: 35 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-TDFN Exposed Pad
• Resistance In Ohms: 100K
• Number Of Pots: Single
• Taps Per Pot: 256
• Resistance: 100 KOhms
• Wiper Memory: Non Volatile
• Digital Interface: Serial (3-Wire, SPI)
• Operating Supply Voltage: 5 V
• Supply Current: 0.001 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Description/function: 100kOhm, 256-Tap, Nonvolatile, SPI-Interface Digital Potentiometer
• Mounting Style: SMD/SMT
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 2.7 V
• Tolerance: 25 %
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MAX5423ETA+T; MAX5423ETA+TTR

Figure 1. Digital Interface and Timing Diagram
The MAX5422/MAX5423/MAX5424 contain a resistor
array with 255 resistive elements. The MAX5422 has a
total end-to-end resistance of 50kΩ; the MAX5423 has
an end-to-end resistance of 100kΩ; and the MAX5424
has an end-to-end resistance of 200kΩ. The
MAX5422/MAX5423/MAX5424 allow access to the high,
low, and wiper terminals for a standard voltage-divider
configuration. H, L, and W can be connected in any
desired configuration as long as their voltages fall
between GND and V
A simple, 3-wire, SPI serial interface moves the wiper
among the 256 tap points. The nonvolatile memory
stores the wiper position and recalls the stored wiper
position upon power-up. The nonvolatile memory is
guaranteed for 50 years for wiper data retention and up
to 200,000 wiper store cycles.
PIN
—
1
2
3
4
5
6
7
8
SCLK
DIN
CS
NAME
SCLK
GND
V
DIN
CS
EP
W
DD
H
L
_______________________________________________________________________________________
t
DD
CS0
Power-Supply Input. Bypass V
Serial-Interface Clock Input
Serial-Interface Data Input
Active-Low Digital-Input Chip Select
Ground
Low Terminal. The voltage at L can be greater than or less than the voltage at H. Current can flow into or
out of L.
Wiper Terminal
High Terminal. The voltage at H can be greater than or less than the voltage at L. Current can flow into or
out of H.
Exposed Pad. The exposed pad is not internally connected. Connect to GND or leave floating.
Detailed Description
.
t
CSS
256-Tap, Nonvolatile, SPI-Interface,
t
DS
t
CL
t
DD
DH
t
CH
with a 0.1µF capacitor from V
The MAX5422/MAX5423/MAX5424 consist of a resistor
array with 255 resistive elements; 256 tap points are
accessible to the wiper, W, along the resistor string
between H and L. Select the wiper tap point by pro-
gramming the potentiometer through the 3-wire (SPI)
interface. Eight data bits, and a control byte program
the wiper position. The H and L terminals of the
MAX5422/MAX5423/MAX5424 are similar to the two
end terminals of a mechanical potentiometer. The
MAX5422/MAX5423/MAX5424 feature power-on reset
circuitry that loads the wiper position from the non-
volatile memory at power-up.
The MAX5422/MAX5423/MAX5424 use a 3-wire, SPI-
compatible, serial data interface (Figure 1 and 2). This
write-only interface contains three inputs: chip-select
Digital Potentiometers
FUNCTION
t
CP
DD
to GND.
t
CSH
Pin Description
Digital Interface
Analog Circuitry
t
CSW
t
CS1
7