MCP4152-103E/P Microchip Technology, MCP4152-103E/P Datasheet - Page 59
![IC POT DGTL SNGL 10K RHEO 8DIP](/photos/6/66/66649/mcp4152-103e_p_sml.jpg)
MCP4152-103E/P
Manufacturer Part Number
MCP4152-103E/P
Description
IC POT DGTL SNGL 10K RHEO 8DIP
Manufacturer
Microchip Technology
Specifications of MCP4152-103E/P
Package / Case
8-DIP (0.300", 7.62mm)
Taps
257
Resistance (ohms)
10K
Number Of Circuits
1
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Volatile
Interface
SPI Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Resistance In Ohms
10K
Number Of Pots
Single
Taps Per Pot
256
Resistance
10 KOhms
Wiper Memory
Volatile
Digital Interface
Serial (SPI)
Operating Supply Voltage
2.5 V, 3.3 V, 5 V
Supply Current
1 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
Through Hole
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
8.0
Digital potentiometers have a multitude of practical
uses in modern electronic circuits. The most popular
uses include precision calibration of set point thresh-
olds, sensor trimming, LCD bias trimming, audio atten-
uation, adjustable power supplies, motor control
overcurrent trip setting, adjustable gain amplifiers and
offset
devices can be used to replace the common mechani-
cal trim pot in applications where the operating and
terminal voltages are within CMOS process limitations
(V
8.1
All inputs that would be used to interface to a Host
Controller support High Voltage on their input pin. This
allows the MCP4XXX device to be used in split power
rail applications.
An example of this is a battery application where the
PIC
(4.8V) and the MCP4XXX device is powered by the
3.3V regulated voltage.
For SPI applications, these inputs are:
• CS
• SCK
• SDI (or SDI/SDO)
• SHDN
Figure 8-1
rail systems. In this system, the MCP4XXX interface
input signals need to be able to support the PIC MCU
output high voltage (V
In Example #1
input signals need to be able to support the PIC MCU
output high voltage (V
becomes too large, then the customer may be required
to do some level shifting due to MCP4XXX V
related to Host Controller V
In Example #2
input signals need to be able to support the lower volt-
age of the PIC MCU output high voltage level (V
Table 8-1
voltage specifications and the MCP4XXX specifica-
tions. So this PIC MCU operating at 3.3V will drive a
V
the V
specifications.
© 2007 Microchip Technology Inc.
OH
DD
®
at 2.64V, and for the MCP4XXX operating at 5.5V,
IH
= 2.7V to 5.5V).
MCU is directly powered by the battery supply
is 2.47V. Therefore, the interface signals meet
trimming.
APPLICATIONS EXAMPLES
Split Rail Applications
shows an example PIC microcontroller I/O
through
(Figure
(Figure
Figure 8-2
The
OH
OH
8-1), the MCP4XXX interface
8-2), the MCP4XXX interface
).
). If the split rail voltage delta
MCP413X/415X/423X/425X
IH
levels.
show three example split
OH
OH
levels
MCP413X/415X/423X/425X
).
FIGURE 8-1:
System 1.
FIGURE 8-2:
System 2.
TABLE 8-1:
5.5
5.0
4.5
3.3
3.0
2.7
Note 1:
V
DD
5V
PIC
2:
3:
4.4
4.0
3.6
2.64 2.64 4.5
2.4
2.16 2.16 5.5
PIC MCU
V
Voltage
Regulator
3V
IH
(1)
SHDN
V
V
V
V
V
V
V
V
The only MCP4XXX output pin is SDO,
which is Open-Drain (or Open-Drain with
Internal Pull-up) with High Voltage Support
PIC MCU
SDO
OH
OL
IH
IL
OH
OL
IH
IL
Voltage
Regulator
SCK
SDI
4.4
4.0
3.6
2.4
CS
V
maximum = 0.2 * V
maximum = 0.2 * V
minimum = 0.8 * V
minimum = 0.45 * V
maximum = 0.6V
maximum = 0.2 * V
SHDN
OH
minimum = 0.8 * V
minimum (SDA only) =;
SDO
V
SCK
SDI
CS
OH
2.7
3.0
3.3
5.0
V
Example Split Rail
Example Split Rail
DD
- V
MCP4XXX
IH
3V
1.215 —
1.35
1.485 —
2.025 —
2.25
2.475 —
V
COMPARISONS
IH
DD
DD
DD
—
—
DD
MCP4XXX
(2)
DD
DD
V
SDI
CS
SCK
SHDN
SDO
DS22060A-page 59
;
;
OH
(3)
(3)
(3)
(3)
(3)
(3)
;
;
MCP4XXX
SDI
CS
SCK
SHDN
SDO
Comment
5V