MCP4642-503E/UN Microchip Technology, MCP4642-503E/UN Datasheet - Page 58
![IC DGTL POT 50K 256TAPS 10-MSOP](/photos/6/59/65940/c04-021-msop_sml.jpg)
MCP4642-503E/UN
Manufacturer Part Number
MCP4642-503E/UN
Description
IC DGTL POT 50K 256TAPS 10-MSOP
Manufacturer
Microchip Technology
Datasheet
1.MCP4541T-502EMF.pdf
(92 pages)
Specifications of MCP4642-503E/UN
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Taps
129
Resistance (ohms)
50K
Number Of Circuits
2
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Resistance In Ohms
50K
Number Of Pots
Dual
Taps Per Pot
128
Resistance
50 KOhms
Wiper Memory
Non Volatile
Digital Interface
Serial (2-Wire, I2C)
Operating Supply Voltage
2.5 V, 3.3 V, 5 V
Supply Current
2.5 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP4642-503E/UN
Manufacturer:
Microchip
Quantity:
500
MCP454X/456X/464X/466X
7.4
The Write Command can be issued to both the Volatile
and Non-Volatile memory locations. The format of the
command, see
Byte, an A bit, the MCP4XXX Command Byte, an A bit,
the MCP4XXX Data Byte, an A bit, and a Stop (or
Restart) condition. The MCP4XXX generates the A / A
bits.
A Write command to a Volatile memory location
changes that location after a properly formatted Write
Command and the A / A clock have been received.
A Write command to a Non-Volatile memory location
will only start a write cycle after a properly formatted
Write Command have been received and the Stop
condition has occurred.
7.4.1
For volatile memory locations, data is written to the
MCP4XXX after every byte transfer (during the
Acknowledge). If a Stop or Restart condition is gener-
ated during a data transfer (before the A), the data will
not be written to the MCP4XXX. After the A bit, the
master can initiate the next sequence with a Stop or
Restart condition.
Refer to
7.4.2
The sequence to write to a single non-volatile memory
location is the same as a single write to volatile memory
with the exception that the EEPROM write cycle (t
started after a properly formatted command, including
the Stop bit, is received. After the Stop condition occurs
the serial interface may immediately be re-enabled by
initiating a Start condition.
During an EEPROM write cycle, access to volatile
memory (addresses 00h, 01h, 04h, and 05h) is allowed
when using the appropriate command sequence.
Commands that address non-volatile memory are
ignored until the EEPROM write cycle (t
This allows the Host Controller to operate on the
Volatile Wiper registers, the TCON register, and to
Read the Status Register. The EEWA bit in the Status
register indicates the status of an EEPROM Write
Cycle.
Once a write command to a Non-Volatile memory
location has been received, No other commands
should be received before the Stop condition occurs.
Figure 7-2
DS22107A-page 58
Note:
Figure 7-2
Write Data
Normal and High Voltage
show the waveform for a single write.
Writes to certain memory locations will be
dependant on the state of the WiperLock
Technology bits and the Write Protect bit.
SINGLE WRITE TO VOLATILE
MEMORY
SINGLE WRITE TO NON-VOLATILE
MEMORY
Figure
for the byte write sequence.
7-2, includes the I
wc
) completes.
2
C Control
wc
) is
7.4.3
A continuous write mode of operation is possible when
writing to the volatile memory registers (address 00h,
01h, and 04h). This continuous write mode allows
writes without a Stop or Restart condition or repeated
transmissions of the I
shows the sequence for three continuous writes. The
writes do not need to be to the same volatile memory
address. The sequence ends with the master sending
a STOP or RESTART condition.
7.4.4
If a continuous write is attempted on Non-Volatile
memory, the missing Stop condition will cause the com-
mand to be an error condition (A). A Start bit is required
to reset the command state machine.
7.4.5
The High Voltage Command (HVC) signal is
multiplexed with Address 0 (A0) and is used to indicate
that the command, or sequence of commands, are in
the High Voltage operational state. High Voltage
commands allow the device’s WiperLock Technology
and write protect features to be enabled and disabled.
The HVC pin has an internal resistor connection to the
MCP45XX/46XXs internal V
CONTINUOUS WRITES TO
VOLATILE MEMORY
CONTINUOUS WRITES TO
NON-VOLATILE MEMORY
THE HIGH VOLTAGE COMMAND
(HVC) SIGNAL
© 2008 Microchip Technology Inc.
2
C Control Byte.
DD
signal.
Figure 7-3