MCP4018T-103E/LT Microchip Technology, MCP4018T-103E/LT Datasheet - Page 38

• Manufacturer Part Number: MCP4018T-103E/LT
• Description: IC DGTL POT 10K 128TAPS SC70-6
• Manufacturer: Microchip Technology

Specifications of MCP4018T-103E/LT

• Package / Case: SC-70-6, SC-88, SOT-363
• Temperature Coefficient: 150 ppm/°C Typical
• Taps: 128
• Resistance (ohms): 10K
• Number Of Circuits: 1
• Memory Type: Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Resistance In Ohms: 10K
• Number Of Pots: Single
• Taps Per Pot: 128
• Resistance: 10 KOhms
• Wiper Memory: Volatile
• Buffered Wiper: Buffered
• Digital Interface: Serial (2-Wire, I2C)
• Operating Supply Voltage: 2.5 V or 3.3 V or 5 V
• Supply Current: 0.045 mA (Typ)
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Description/function: 7 Bit Single I2C Digital Potentiometer
• Mounting Style: SMD/SMT
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Tolerance: 20 %
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: MCP4018T-103E/LTTR

MCP4017/18/19
5.4.1
The write operation requires the START condition,
Control Byte, Acknowledge, Data Byte, Acknowledge
and STOP (or RESTART) condition. The Control (Slave
Address) Byte requires the R/W bit equal to a logic zero
(R/W = “0”) to generate a write sequence. The
MCP4017/18/19 is responsible for generating the
Acknowledge (A) bits.
Data is written to the MCP4017/18/19 after every byte
transfer (during the A bit). If a STOP or RESTART
condition is generated during a data transfer (before
the A bit), the data will not be written to MCP4017/18/
19.
Data bytes may be written after each Acknowledge.
The command is terminated once a Stop (P) condition
occurs. Refer to
For a single byte write, the master sends a STOP or
RESTART condition after the 1st data byte is sent.
The MSb of each Data Byte is a don’t care, since the
wiper register is only 7-bits wide.
Figure 5-14
the Master Device and the MCP4017/18/19 device and
the resultant I
FIGURE 5-12:
DS22147A-page 38
Legend
S = Start Condition
P = Stop Condition
A = Acknowledge
X = Don’t Care
R/W = Read/Write bit
D6, D5, D4, D3, D2, D1, D0 = Data bits
S
WRITE OPERATION
shows the I
2
C bus values.
0 1 0
Figure 5-12
Slave Address Byte
Fixed
Address
I
x D6 D5 D4
2
2
C Write Command Format.
C communication behavior of
1
Data Byte
1
for the write sequence.
1 1
D3 D2 D1 D0
0
A
Read/Write bit (“0” = Write)
x D6 D5 D4
A
Data Byte
x D6 D5 D4
Data Byte
D3
5.4.2
The read operation requires the START condition,
Control Byte, Acknowledge, Data Byte, the master
generating the A and STOP condition. The Control
Byte requires the R/W bit equal to a logic one (R/W =
1) to generate a read sequence. The MCP4017/18/19
will A the Slave Address Byte and A all the Data Bytes.
The I
last Data Byte. If there are multiple Data Bytes, the I
Master will A all Data Bytes except the last Data Byte
(which it will A).
The MCP4017/18/19 maintains control of the SDA
signal until all data bits have been clocked out.
The command is terminated once a Stop (P) condition
occurs. Refer to
sequence. For a single read, the master sends a STOP
or RESTART condition after the 1st data byte (and A
bit) is sent from the slave.
Figure 5-14
the Master Device and the MCP4017/18/19 device and
the resultant I
D2 D1 D0 A
2
D3
C Master will A the Slave Address Byte and the
D2 D1 D0 A P
READ OPERATIONS
shows the I
2
C bus values.
x D6 D5 D4
Figure 5-13
Data Byte
STOP bit
2
© 2009 Microchip Technology Inc.
C communication behavior of
D3
for the read command
D2 D1 D0 A
2
C