MCP4261T-502E/ST Microchip Technology, MCP4261T-502E/ST Datasheet - Page 54
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP4261T-502E/ST
Manufacturer Part Number
MCP4261T-502E/ST
Description
IC DGTL POT 5K 2CH 14TSSOP
Manufacturer
Microchip Technology
Datasheet
1.MCP4161-502ESN.pdf
(88 pages)
Specifications of MCP4261T-502E/ST
Package / Case
14-TSSOP
Taps
257
Resistance (ohms)
5K
Number Of Circuits
2
Temperature Coefficient
150 ppm/°C Typical
Memory Type
Non-Volatile
Interface
SPI Serial
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Resistance In Ohms
5K
Number Of Pots
Dual
Taps Per Pot
256
Resistance
5 KOhms
Wiper Memory
Non Volatile
Digital Interface
Serial (4-Wire, SPI)
Operating Supply Voltage
2.5 V, 3.3 V, 5 V
Supply Current
550 uA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MCP4261T-502-E/ST
MCP4261T-502-E/STTR
MCP4261T-502-E/STTR
MCP4261T-502E/STTR
MCP4261T-502-E/STTR
MCP4261T-502-E/STTR
MCP4261T-502E/STTR
MCP414X/416X/424X/426X
7.7.2
Continuous Increments are possible only when writing
to the volatile memory registers (address 00h, and
01h).
Figure 7-7
for three continuous writes. The writes do not need to
be to the same volatile memory address.
When executing an continuous Increment commands,
the selected wiper will be altered from n to n+1 for each
Increment command received. The wiper value will
increment up to 100h on 8-bit devices and 80h on 7-bit
devices. After the wiper value has reached Full-Scale
(8-bit =100h, 7-bit =80h), the wiper value will not be
incremented further. If the Wiper register has a value
between 101h and 1FFh, the Increment command is
disabled.
FIGURE 7-7:
DS22059B-page 54
SDI
SDO
A
D
3
1
1
1
1
Note 1: Only functions when writing the volatile wiper registers (AD3:AD0) 0h and 1h.
(INCR COMMAND (n+1) )
shows a Continuous Increment sequence
CONTINUOUS INCREMENTS
A
D
2
1
1
1
1
COMMAND BYTE
2: Valid Address/Command combination.
3: Invalid Address/Command combination.
4: If an Error Condition occurs (CMDERR = L), all following SDO bits will be low until the CMDERR
D
A
1
1
1
1
1
condition is cleared (the CS pin is forced to the inactive state).
D
A
0
1
1
1
1
Continuous Increment Command - SDI and SDO States.
0
1
1
1
1
1
1 1* 1
1
1
1
X
0
1
1
X
0
1
1
D
A
3
1
0
1
1
(INCR COMMAND (n+2) )
D
A
2
1
0
1
1
COMMAND BYTE
D
A
1
1
0
1
1
A
D
0
1
0
1
1
0
1
0
1
1
1
1 1* 1
0
1
1
Increment commands can be sent repeatedly without
raising CS until a desired condition is met. The value in
the Volatile Wiper register can be read using a Read
Command
Non-Volatile Wiper EEPROM using a Write Command.
When executing a continuous command string, The
Increment command can be followed by any other valid
command.
The wiper terminal will move after the command has
been received (8th clock).
After the wiper is incremented to the desired position,
the CS pin should be forced to V
unexpected transitions (on the SCK pin do not cause
the wiper setting to change). Driving the CS pin to V
should occur as soon as possible (within device
specifications) after the last desired increment occurs.
X
0
0
1
X
0
0
1
D
A
3
1
0
0
1
(INCR COMMAND (n+3) )
A
D
2
1
0
0
1
and
COMMAND BYTE
A
D
1
1
0
0
1
written
A
D
0
1
0
0
1
© 2008 Microchip Technology Inc.
0
1
0
0
1
1 1* 1 Note 1, 2
1
1
0
0
to
X
0
0
0
the
IH
X
0 Note 3, 4
0 Note 3, 4
0 Note 3, 4
to ensure that
corresponding
IH