DS1809U-050+T&R Maxim Integrated Products, DS1809U-050+T&R Datasheet - Page 2
![IC DALLASTAT 50K 8-USOP](/photos/1/39/13936/406-8-msop_sml.jpg)
DS1809U-050+T&R
Manufacturer Part Number
DS1809U-050+T&R
Description
IC DALLASTAT 50K 8-USOP
Manufacturer
Maxim Integrated Products
Series
Dallastat™r
Datasheet
1.DS1809-010.pdf
(9 pages)
Specifications of DS1809U-050+T&R
Taps
64
Resistance (ohms)
50K
Number Of Circuits
1
Temperature Coefficient
750 ppm/°C Typical
Memory Type
Non-Volatile
Interface
Contact Closure
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Resistance In Ohms
50K
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
DS1809
The DS1809 is available in standard 10 k, 50 k, and 100 kresistor versions. The DS1809 is
provided as an industrial temperature grade part only. Available packaging for the DS1809 include an 8-
lead (300-mil) DIP an 8-lead (150-mil) SOIC, and an 8-lead (118-mil) SOP.
BLOCK DIAGRAM Figure 1
OPERATION
The DS1809 Dallastat is a digitally controlled, nonvolatile potentiometer. A block diagram of the
DS1809 is shown in Figure 1. The DS1809 is a linear potentiometer providing 64-uniform wiper
positions over the entire resistor range including the end-terminals. All three potentiometer terminals of
the device are accessible. These terminals include R
, R
, and R
. R
and R
are the end-terminals of the
H
L
W
H
L
potentiometer. These terminals will have a constant resistance between them as defined by the
potentiometer value chosen: 10 k, 50 k, or the 100 kversion. Functionally, R
and R
are
H
L
interchangeable. The wiper terminal, R
, is the multiplexed terminal and can be set to one of the 64 total
W
positions that exist on the resistor ladder including the R
and R
terminals.
H
L
Control of the wiper (R
) position setting is accomplished via the two inputs UC and DC. The UC and
W
DC control inputs, when active, determine the direction on the resistor array that the wiper position will
move. The UC (up control) control input is used to move the wiper position towards the R
terminal. The
H
DC (down control) control input is used to move wiper position towards the R
terminal.
L
The control inputs UC and DC are active low inputs that interpret input pulse widths as the means of
controlling wiper movement. Internally, these inputs are pulled up to V
via a 100 kresistance. A
CC
transition from a high-to-low on these inputs is considered the beginning of pulse input activity.
A single pulse on the UC or DC input is defined as being greater than 1 millisecond but lasting no longer
that ½ second. This type pulse input will cause the wiper position of the Dallastat to move one position.
Multiple pulse inputs (repetitive pulse inputs) can be used to step through each wiper position of the
device. The requirement for a repetitive pulse train on the UC or DC inputs is that pulses must be
separated by a minimum high time of 1 millisecond. If this is not the case the Dallastat will ignore that
pulse input.
A continuous pulse input (“push and hold”) is defined as lasting longer that ½ second. A continuous pulse
input will cause the wiper position to move one position every 100 milliseconds following the initial ½-
2 of 9