MCZ33903BS5EK Freescale Semiconductor, MCZ33903BS5EK Datasheet - Page 55
![no-image](/images/manufacturer_photos/0/2/262/freescale_semiconductor_sml.jpg)
MCZ33903BS5EK
Manufacturer Part Number
MCZ33903BS5EK
Description
SBC W/HIGH SPEED CAN 5V
Manufacturer
Freescale Semiconductor
Series
-r
Datasheet
1.MCZ33904A5EKR2.pdf
(98 pages)
Specifications of MCZ33903BS5EK
Main Purpose
Power Management, System Interface
Embedded
No
Utilized Ic / Part
MCZ33903
Primary Attributes
CAN Transceiver
Secondary Attributes
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
bus applications.
includes as well as a fast baud rate for test and programming
modes. It has excellent ESD robustness and immunity
against disturbance, and radiated emission performance. It
has safe behavior in case of a LIN bus short-to-ground, or a
LIN bus leakage during low power mode.
POWER SUPPLY PIN (VSUP2)
avoid a false bus message, an under-voltage on VSUP2
disables the transmission path (from TXD to LIN) when V
falls below 6.1 V.
GROUND PIN (GND)
LIN interface do not have significant current consumption on
the LIN bus pin when in the recessive state.
LIN BUS PIN (LIN1, LIN2)
receiver. It is suited for automotive bus systems, and is
compliant to the LIN bus specification 2.1 and SAEJ2602-2.
Driver Characteristics
current thermal shutdown. An internal pull-up resistor with a
serial diode structure is integrated so no external pull-up
components are required for the application in a slave node.
An additional pull-up resistor of 1.0 kΩ must be added when
the device is used in the master node. The 1.0 kΩ pull-up
resistor can be connected to the LIN pin or to the ECU battery
supply.
receiver and LIN disable modes.
TRANSMIT RECEIVE
receive information.
timing are compatible with LIN protocol specification 2.1.
timing are compatible with J2602-2.
Analog Integrated Circuit Device Data
Freescale Semiconductor
The physical interface is dedicated to automotive LIN sub-
The interface has 20 kbps and 10 kbps baud rates, and
Digital inputs are related to the device VDD pin.
The VSUP2 pin is the supply pin for the LIN interface. To
In case of a ground disconnection at the module level, the
The LIN pin represents the single-wire bus transmitter and
The LIN interface is only active during Normal mode.
The LIN driver is a low side MOSFET with internal over-
The LIN interface have two operational modes, Transmit
In the TxD/RxD mode, the LIN bus can transmit and
When the 20 kbps baud rate is selected, the slew rate and
When the 10 kbps baud rate is selected, the slew rate and
LIN INTERFACE DESCRIPTION
LIN OPERATIONAL MODES
LIN BLOCK
SUP
line to V
disconnection.
which are selected by SPI.
Receiver Characteristics
V
enters into a recessive state even if communication is sent on
TXD.
threshold, the transceiver and receiver are disabled. When
the temperature falls below the over-temperature threshold,
LIN driver and receiver will be automatically enabled.
DATA INPUT PIN (TXDL1, TXDL2)
control the state of the LIN output. When TXDL is LOW
(dominant), LIN output is LOW. When TXDL is HIGH
(recessive), the LIN output transistor is turned OFF.
force the recessive state if the input pin is left floating.
the LIN transmitter goes automatically in recessive state. This
is reported by flag in LIN register.
DATA OUTPUT PIN (RXDL1, RXDL2)
the state of the LIN bus voltage.
RXD, LIN LOW (dominant) is reported by a low voltage on
RXD.
timing are much faster than the above specification and allow
fast data transition. The LIN interface can be set by the SPI
command in TxD/RxD mode, only when TXDL is at a high
level. When the SPI command is send while TXDL is low, the
command is ignored.
SLEEP MODE
disabled. Supply current for LIN block from V
(typ 3.0 μA). LIN bus is monitor to detect wake-up event. In
SUP2
The LIN pin exhibits no reverse current from the LIN bus
The transmitter has a 20 kbps, 10 kbps and fast baud rate,
The receiver thresholds are ratiometric with the device
If the V
If LIN driver temperature reaches the over-temperature
The TXDl1 (TXDL2) input pin is the MCU interface to
This pin has an internal pull-up current source to V
If the pin stays low (dominant sate) more than t
The RXDl output pin is the MCU interface, which reports
LIN HIGH (recessive) is reported by a high voltage on
When the fast baud rate is selected, the slew rate and
This mode is selected by SPI, and the transmission path is
voltage.
SUP2
SUP2
, even in the event of a GND shift or V
voltage goes below typ 6.1 V, the LIN bus
LIN INTERFACE DESCRIPTION
SUP2
LIN BLOCK
is very low
TXDDOM
SUP2
33903/4/5
DD
to
,
55