RD4247MAG3110 Freescale Semiconductor, RD4247MAG3110 Datasheet - Page 14

• Manufacturer Part Number: RD4247MAG3110
• Description: DEV KIT MAG3110 LFSTBUSB
• Manufacturer: Freescale Semiconductor
• Series: -r

Specifications of RD4247MAG3110

• Sensor Type: Accelerometer, 3 Axis
• Sensing Range: ±10g
• Interface: I²C
• Sensitivity: 1mg/bit
• Voltage - Supply: 1.95 V ~ 3.6 V
• Embedded: No
• Utilized Ic / Part: MAG3110
• Features: LFSTBUSB For Communication To PC, MAG3110FC & MMA8451Q For System Calibration
• Peak Reflow Compatible (260 C): Yes
• Rohs Compliant: Yes
• Application Sub Type: Magnetic Sensor
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Table 25. OFF_Z_MSB Register
Table 26. OFF_Z_LSB Register
5.4
5.4.1
127°C but the output range is from -40°C to 125°C.
Table 27. TEMP Register
5.5
5.5.1
Note: Except for STANDBY mode selection (Bit 0, AC), the device must be in STANDBY mode to change any of the fields within
CTRL_REG1 (0x10).
Table 28. CTRL_REG1 Register
Table 29. CTRL_REG1 Description
Sensors
Freescale Semiconductor
Temperature °C expressed as an 8-bit 2's complement number. Note: The register allows for temperatures from -128°C to
OS [1:0]
DR[2:0]
ZD14
Bit 7
Bit 7
Bit 7
Bit 7
ZD6
DR2
TM
AC
FR
T7
Temperature
Control Registers
DIE_TEMP (0x0F)
CTRL_REG1 (0x10)
Data rate selection. Default value: 000.
See
This register configures the over sampling ratio or measurement integration time.
Default value: 00.
See
Fast Read selection. Default value: 0.
0: The full 16-bit values are read.
1: Fast Read, 8-bit values read from the MSB registers.
Trigger immediate measurement. Default value: 0
0: Normal operation based on AC condition.
1: Trigger measurement.
If part is in ACTIVE mode, any measurement in progress will continue with the highest ODR possible for the selected OSR.
In STANDBY mode triggered measurement will occur immediately and part will return to STANDBY mode as soon as the
measurement is complete.
Operating mode selection. Note: see
0: STANDBY mode.
1: ACTIVE mode.
ACTIVE mode will make periodic measurements based on values programmed in the Data Rate (DR) and Over Sampling
Ratio bits (OS).
Table 30
Table 30
ZD13
Bit 6
Bit 6
Bit 6
Bit 6
DR1
ZD5
T6
for more information.
for more information.
ZD12
Bit 5
Bit 5
Bit 5
Bit 5
DR0
ZD4
T5
section 4.3.5
ZD11
Bit 4
Bit 4
Bit 4
Bit 4
OS1
ZD3
T4
for details. Default value: 0.
ZD10
Bit 3
Bit 3
Bit 3
Bit 3
OS0
ZD2
T3
Bit 2
Bit 2
Bit 2
Bit 2
ZD9
ZD1
FR
T2
Bit 1
Bit 1
Bit 1
Bit 1
ZD8
ZD0
TM
T1
Bit 0
Bit 0
Bit 0
Bit 0
MAG3110
ZD7
AC
T0
0
14