CAT5118TBI-00-T3 ON Semiconductor, CAT5118TBI-00-T3 Datasheet - Page 2

• Manufacturer Part Number: CAT5118TBI-00-T3
• Description: IC POT DIGITL 100K 32TAP SOT23-5
• Manufacturer: ON Semiconductor

Specifications of CAT5118TBI-00-T3

• Taps: 32
• Resistance (ohms): 100K
• Number Of Circuits: 1
• Temperature Coefficient: 200 ppm/°C Typical
• Memory Type: Volatile
• Interface: 2-Wire Serial, Up/Down
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Resistance In Ohms: 100K
• Number Of Elements: 1
• # Of Taps: 32
• Resistance (max): 100KOhm
• Power Supply Requirement: Single
• Interface Type: Serial (2-Wire)
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 5
• Package Type: SOT-23
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: CAT5118TBI-00-T3CT

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Derate 3.1 mW/°C above T
Table 1. PIN DESCRIPTIONS
Table 2. ABSOLUTE MAXIMUM RATINGS
V
All Other Pins to GND
Input and Output Latch−Up Immunity
Maximum Continuous Current into H, L and W
Continuous Power Dissipation (T
Operating Temperature Range
Junction Temperature
Storage Temperature Range
Soldering Temperature (soldering, 10 sec)
CAT5110/
CAT5125
DD
to GND
1
2
3
4
−
5
6
100 kW
50 kW
10 kW
5−pin SC−70 (Note 1)
6−pin SC−70 (Note 1)
Pin Number
CAT5118/
CAT5123
1
2
3
4
−
−
6
A
= +70°C
CAT5119/
A
GND
CAT5124
V
U/D
Parameters
CS
= +70°C)
DD
1
2
3
4
5
−
6
Name
Figure 1. Functional Diagram
GND
V
U/D
Pin
CS
W
H
DD
L
http://onsemi.com
Power Supply
Ground
Up/Down Control Input. With CS low, a low−to−high transition increments
or decrements the wiper position.
Chip Select Input. A high−to−low CS transition determines the mode:
increment if U/D is high, or decrement if U/D is low.
Low Terminal of Resistor
Wiper Terminal of Resistor
High Terminal of Resistor
2
H
L
−0.3 to (V
W
Description
−65 to +150
−40 to +85
−0.3 to +6
Ratings
±200
+150
+300
±0.6
±1.3
±1.3
247
245
DD
+ 0.3)
Units
mW
mA
mA
°C
°C
°C
°C
V
V