MAX5441AEUA+ Maxim Integrated Products, MAX5441AEUA+ Datasheet - Page 8
![IC DAC 16BIT 5V SERIAL 8-UMAX](/photos/1/39/13936/406-8-msop_sml.jpg)
MAX5441AEUA+
Manufacturer Part Number
MAX5441AEUA+
Description
IC DAC 16BIT 5V SERIAL 8-UMAX
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX5441AEUA.pdf
(12 pages)
Specifications of MAX5441AEUA+
Settling Time
1µs
Number Of Bits
16
Data Interface
MICROWIRE™, QSPI™, Serial, SPI™
Number Of Converters
1
Voltage Supply Source
Single Supply
Power Dissipation (max)
362mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
to a standard R-2R ladder, allowing unbuffered opera-
tion in medium-load applications.
The MAX5442/MAX5444 provide matched bipolar offset
resistors, which connect to an external op amp for bipo-
lar output swings (Figure 2b).
The MAX5441–MAX5444 digital interface is a standard
3-wire connection compatible with SPI/QSPI/
MICROWIRE interfaces. The chip-select input (CS)
frames the serial data loading at the data-input pin
(DIN). Immediately following CS’s high-to-low transition,
the data is shifted synchronously and latched into the
input register on the rising edge of the serial clock input
(SCLK). After 16 data bits have been loaded into the
serial input register, it transfers its contents to the DAC
latch on CS’s low-to-high transition (Figure 3). Note that
if CS is not kept low during the entire 16 SCLK cycles,
data will be corrupted. In this case, reload the DAC
latch with a new 16-bit word.
A 20ns (min) logic-low pulse on CLR asynchronously
clears the DAC buffer to code 0 in the MAX5441/
MAX5443 and to code 32768 in the MAX5442/ MAX5444.
The MAX5441–MAX5444 operate with external voltage
references from 2V to V
determines the DAC’s full-scale output voltage.
The power-on reset circuit sets the output of the
MAX5441/MAX5443 to code 0 and the output of the
+3V/+5V, Serial-Input,
Voltage-Output, 16-Bit DACs
Figure 3. MAX5441–MAX5444 3-Wire Interface Timing Diagram
8
_______________________________________________________________________________________
SCLK
DIN
CS
DD
. The reference voltage
D15
External Reference
D14 D13 D12 D11 D10 D9
MSB
Clearing the DAC
Digital Interface
Power-On Reset
D8
D7 D6 D5 D4 D3 D2 D1 D0
MAX5442/MAX5444 to code 32768 when V
applied. This ensures that unwanted DAC output volt-
ages will not occur immediately following a system
power-up, such as after a loss of power.
The MAX5441–MAX5444 operate with external voltage
references from 2V to V
mance if certain guidelines are followed when selecting
and applying the reference. Ideally, the reference’s
temperature coefficient should be less than
0.1ppm/°C to maintain 16-bit accuracy to within 1LSB
over the -40°C to +85°C extended temperature range.
Since this converter is designed as an inverted R-2R volt-
age-mode DAC, the input resistance seen by the voltage
reference is code-dependent. In unipolar mode, the
worst-case input-resistance variation is from 11.5kΩ (at
code 8555hex) to 200kΩ (at code 0000hex). The maxi-
mum change in load current for a 2.5V reference is 2.5V /
11.5k Ω = 217µA; therefore, the required load regulation
is 7ppm/mA for a maximum error of 0.1LSB. This implies
a reference output impedance of less than 18mΩ. In
addition, the impedance of the signal path from the volt-
age reference to the reference input must be kept low
because it contributes directly to the load-regulation
error.
The requirement for a low-impedance voltage reference
is met with capacitor bypassing at the reference inputs
and ground. A 0.1µF ceramic capacitor with short leads
between REF and GND provides high-frequency
bypassing. A surface-mount ceramic chip capacitor is
preferred because it has the lowest inductance. An
SUB-BITS
Applications Information
Reference and Ground Inputs
LSB
UPDATED
DD
DAC
, and maintain 16-bit perfor-
DD
is first