SLCF064JI-F STEC, SLCF064JI-F Datasheet - Page 40
![no-image](/images/no-image-200.jpg)
SLCF064JI-F
Manufacturer Part Number
SLCF064JI-F
Description
Manufacturer
STEC
Type
CompactFlashr
Datasheet
1.SLCF064JI-F.pdf
(46 pages)
Specifications of SLCF064JI-F
Density
64MByte
Operating Supply Voltage (typ)
3.3/5V
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Package Type
Not Required
Mounting
Socket
Pin Count
50
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
3.18/4.75V
Operating Supply Voltage (max)
3.465/5.25V
Programmable
Yes
Lead Free Status / Rohs Status
Not Compliant
SLCF064J(I)
Check Power Mode
(code: E5h or 98h)
This command checks the power mode.
Execute Drive Diagnostic
(code: 90h)
This command performs the internal diagnostic tests
implemented by the card. See ERROR register for dianostic
codes.
Erase Sector(s)
(code: C0h)
This command is used to pre-erase and condition data
sectors in advance.
XXXXH: These values are dependent upon the the specific card.
Address
69-255
Word
10-19
23-46
60-61
7-8
2 0
2 1
2 2
4 7
4 8
4 9
5 0
5 1
5 2
5 3
5 4
5 5
5 6
5 7
5 8
5 9
6 2
6 3
6 4
6 5
6 6
6 7
6 8
0
1
2
3
4
5
6
9
848AH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
XXXXH
00XXH
010XH
0000H
0000H
0001H
0001H
0004H
0001H
0000H
0300H
0000H
0200H
0000H
0000H
0407H
0003H
0000H
0000H
0078H
0078H
0000H
XXXH
0003h
Data
Bytes
Total
388
2 0
4 8
2
2
2
2
2
2
2
4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
2
2
2
2
2
2
2
General configuration bit-significant information—value fixed by CFA
Default number of cylinders
Reserved
Default number of heads
Number of unformatted bytes per track (not used)
Number of unformatted bytes per sector (not used)
Default number of sectors per track
Number of sectors per card (word7=MSW, word 8 = LSW)
Reserved
Serial Number
Buffer type (dual ported, multi-sector, with read cache)
Buffer size in 512 byte increments
# of ECC bytes passed on Read/Write Long commands
Firmware revision and model number in ASCII
Maximum of 1 sector on Read/Write Multiple command
Double Word not supported
Capabilities: DMA not supported (bit 8), LBA supported (bit 9)
Reserved
PIO data transfer cycle timing mode
Single word DMA data transfer cycle timing mode (not supported)
Words 54 - 58 and 64 - 70 are valid
Number of Current Cylinders
Number of Current Heads
Number of Current Sectors Per Track
LSW of the Current Capacity in Sectors
MSW of the Current Capacity in Sectors
Current Setting for Block Count=1 for R/W Multiple commands
Total number of sectors addressable in LBA Mode
Single word DMA transfer not supported
Multiword DMA modes active; modes 0-2 supported
Advanced PIO modes supported (modes 3 and 4)
Minimum multiword DMA transfer cycle time per word (ns)
Recommended multiword DMA transfer cycle time per word (ns)
Minimum PIO transfer without flow control
Minimum PIO transfer with IORDY flow control
Reserved
Identify Drive Information (Typical)
Document Part Number 61000-02805-304 July 2004
Format Track
(code: 50h)
This command writes the desired head and cylinder of the
selected drive with a vender unique data pattern (typically
00h or FFh). This card accepts a sector buffer of data from the
host to follow the command with the same protocol as the
Write Sector Command although the information in the
buffer is not used.
Identify Drive
(code: ECh)
This command enables the host to receive parameter
information from the card. (See table below.)
Description
COMPACTFLASH
Page 40