AD660BR-REEL Analog Devices Inc, AD660BR-REEL Datasheet - Page 4

• Manufacturer Part Number: AD660BR-REEL
• Description: IC DAC 16BIT MONO W/VREF 24-SOIC
• Manufacturer: Analog Devices Inc
• Series: DACPORT®r

Specifications of AD660BR-REEL

• Rohs Status: RoHS non-compliant
• Settling Time: 6µs
• Number Of Bits: 16
• Data Interface: Serial
• Number Of Converters: 1
• Voltage Supply Source: Analog and Digital, Dual ±
• Power Dissipation (max): 625mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)

AD660
Parameter
POWER SUPPLIES
TEMPERATURE RANGE
1
2
3
4
5
6
AC PERFORMANCE CHARACTERISTICS
With the exception of total harmonic distortion + noise (THD + N) and signal-to-noise (SNR) ratio, these characteristics are included for
design guidance only and are not subject to test. THD + N and SNR are 100% tested.
T
Table 2.
Parameter
OUTPUT SETTLING TIME
TOTAL HARMONIC DISTORTION + NOISE
SIGNAL-TO-NOISE RATIO
DIGITAL-TO-ANALOG GLITCH IMPULSE
DIGITAL FEEDTHROUGH
OUTPUT NOISE VOLTAGE
REFERENCE NOISE
For 16-bit resolution, 1 LSB = 0.0015% of FSR. For 15-bit resolution, 1 LSB = 0.003% of FSR. For 14-bit resolution, 1 LSB = 0.006% of FSR. FSR stands for full-scale range
and is 10 V in a unipolar mode and 20 V in bipolar mode.
Gain error and gain drift are measured using the internal reference. The internal reference is the main contributor to gain drift. If lower gain drift is required, the AD660
can be used with a precision external reference such as the AD587, AD586, or AD688.
Gain error is measured with fixed 50 Ω resistors as shown in the Theory of Operation section. Eliminating these resistors increases the gain error by 0.25% of FSR
(unipolar mode) or 0.50% of FSR (bipolar mode).
DAC gain error and drift are measured with an external voltage reference. They represent the error contributed by the DAC alone, for use with an external reference.
External current is defined as the current available in addition to that supplied to REF IN and SPAN/BIPOLAR OFFSET on the AD660.
Operation on ±12 V supplies is possible using an external reference such as the AD586 and reducing the output range. Refer to the Internal/External Reference Use
section.
MIN
Voltage
Current (No Load)
Power Supply Sensitivity
Power Dissipation (Static, No Load)
Specified Performance (A, B)
Specified Performance (S)
(Time to ±0.0008% FS
with 2 kΩ, 1000 pF Load)
A, B, S Grade
A, B, S Grade
A, B, S Grade
Density (1 kHz to 1 MHz)
+V
−V
+V
I
I
I
≤ T
CC
EE
LL
@ V
@ V
CC
EE
LL
A
6
6
IH
IH
≤ T
= 5 V, V
= 2.4 V, V
MAX
, +V
IL
= 0 V
IL
CC
= 0.4 V
= 15 V, −V
EE
= −15 V, +V
15
Limit
13
8
10
6
8
2.5
0.009
0.056
5.6
83
2
120
125
LL
= 5 V except where noted.
Unit
μs max
μs typ
μs typ
μs typ
μs typ
μs typ
% max
% max
% max
dB min
nV-s typ
nV-s typ
nV/√Hz typ
nV/√Hz typ
Rev. B | Page 4 of 20
Min
+13.5
−13.5
+4.5
−40
−55
AD660AN/AR/SQ
Test Conditions/Comments
20 V step, T
20 V step, T
20 V step, T
10 V step, T
10 V step, T
1 LSB step, T
0 dB, 990.5 Hz, sample rate = 96 kHz, T
−20 dB, 990.5 Hz, sample rate = 96 kHz, T
−60 dB, 990.5 Hz, sample rate = 96 kHz, T
T
DAC alternately loaded with 0x8000 and 0x7FFF
DAC alternately loaded with 0x0000 and 0xFFFF, CS high
Measured at V
Measured at REF OUT
Typ
+12
−12
0.3
3
1
365
A
= 25°C
A
A
MIN
A
MIN
MIN
= 25°C
= 25°C
= 25°C
Max
+16.5
−16.5
+5.5
+18
−18
2
7.5
2
625
+85
+125
≤ T
≤ T
OUT
≤ T
, 20 V span, excludes reference
A
A
A
≤ T
≤ T
≤ T
MAX
MAX
MAX
Min
+13.5
−13.5
+4.5
−40
AD660BN/BR
Typ
+12
−12
0.3
3
1
365
A
= 25°C
A
A
= 25°C
= 25°C
Max
2
+16.5
−16.5
+5.5
+18
−18
2
7.5
625
+85
Unit
V
V
V
mA
mA
mA
mA
ppm/%
mW
°C
°C