AD664BD-BIP Analog Devices Inc, AD664BD-BIP Datasheet - Page 6
![IC DAC 12BIT QUAD MONO 28-CDIP](/photos/6/62/66275/505-28-cdip_heat_pad_sml.jpg)
AD664BD-BIP
Manufacturer Part Number
AD664BD-BIP
Description
IC DAC 12BIT QUAD MONO 28-CDIP
Manufacturer
Analog Devices Inc
Datasheet
1.AD664JNZ-BIP.pdf
(20 pages)
Specifications of AD664BD-BIP
Data Interface
Parallel
Rohs Status
RoHS non-compliant
Settling Time
8µs
Number Of Bits
12
Number Of Converters
4
Voltage Supply Source
Dual ±
Power Dissipation (max)
525mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Package / Case
28-CDIP (0.600", 15.24mm)
Resolution (bits)
12bit
Sampling Rate
125kSPS
Supply Voltage Range - Digital
4.5V To 5.5V
Supply Current
15mA
Digital Ic Case Style
DIP
No. Of Pins
28
Number Of Channels
4
Resolution
12b
Conversion Rate
125KSPS
Interface Type
Parallel
Single Supply Voltage (typ)
Not RequiredV
Dual Supply Voltage (typ)
±15V
Architecture
R-2R
Power Supply Requirement
Dual
Output Type
Voltage
Integral Nonlinearity Error
±0.75LSB
Single Supply Voltage (min)
Not RequiredV
Single Supply Voltage (max)
Not RequiredV
Dual Supply Voltage (min)
±11.4V
Dual Supply Voltage (max)
±16.5V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Through Hole
Pin Count
28
Package Type
CDIP
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD664BD-BIP
Manufacturer:
ADI
Quantity:
558
Part Number:
AD664BD-BIP
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD664
ANALOG CIRCUIT CONSIDERATIONS
Grounding Recommendations
The AD664 has two pins, designated ANALOG and DIGITAL
ground. The analog ground pin is the “high quality” ground ref-
erence point for the device. A unique internal design has
resulted in low analog ground current. This greatly simplifies
management of ground current and the associated induced volt-
age drops. The analog ground pin should be connected to the
analog ground point in the system. The external reference and
any external loads should also be returned to analog ground.
The digital ground pin should be connected to the digital
ground point in the circuit. This pin returns current from the
logic portions of the AD664 circuitry to ground.
Analog and digital grounds should be connected at one point in
the system. If there is a possibility that this connection be bro-
ken or otherwise disconnected, then two diodes should be con-
nected between the analog and digital ground pins of the
AD664 to limit the maximum ground voltage difference.
Power Supplies and Decoupling
The AD664 requires three power supplies for proper operation.
V
+5 volts. V
cuitry and require +12 V to +15 V and –12 V to –15 V, respec-
tively. V
then the maximum reference and output voltages anticipated.
Decoupling capacitors should be used on all power supply pins.
Good engineering practice dictates that the bypass capacitors be
located as near as possible to the package pins. V
bypassed to digital ground. V
analog ground.
Driving the Reference Input
The reference input of the AD664 can have an impedance as
low as 1.3 k . Therefore, the external reference voltage must be
able to source up to 7.7 mA of load current. Suitable choices
include the 5 V AD586, the 10 V AD587 and the 8.192 V
AD689.
The architecture of the AD664 derives an inverted version of
the reference voltage for some portions of the internal circuitry.
This means that the power supplies must be at least 2 V
LL
powers the logic portions of the device and requires
CC
Figure 2. Recommended Circuit Schematic
CC
and V
and V
EE
EE
must also be a minimum of two volts greater
power the remaining portions of the cir-
CC
and V
EE
should be decoupled to
LL
should be
–6–
greater than both the external reference and the inverted exter-
nal reference.
Output Considerations
Each DAC output can source or sink 5 mA of current to an
external load. Short-circuit protection limits load current to a
maximum load current of 40 mA. Load capacitance of up to
500 pF can be accommodated with no effect on stability.
Should an application require additional output current, a cur-
rent boosting element can be inserted into the output loop with
no sacrifice in accuracy. Figure 3 details this method.
AD664 output voltage settling time is 10 s maximum. Figure 4
shows the output voltage settling time with a fixed 10 V refer-
ence, gain = 1 and all bits switched from 1 to 0.
Alternately, Figure 5 shows the settling characteristics when the
reference is switched and the input bits remain fixed. In this
case, all bits are “on,” the gain is 1 and the reference is switched
from –5 V to +5 V.
Figure 4. Settling Time; All Bits Switched from On to Off
Figure 5. Settling Time; Input Bits Fixed, Reference
Switched
Figure 3. Current-Boosting Scheme
REV. C