AD6653-150EBZ Analog Devices Inc, AD6653-150EBZ Datasheet - Page 27

• Manufacturer Part Number: AD6653-150EBZ
• Manufacturer: Analog Devices Inc

Specifications of AD6653-150EBZ

• Lead Free Status / Rohs Status: Compliant

If the internal reference of the AD6653 is used to drive multiple
converters to improve gain matching, the loading of the reference
by the other converters must be considered. Figure 54 depicts
how the internal reference voltage is affected by loading.
External Reference Operation
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or improve thermal drift charac-
teristics. Figure 55 shows the typical drift characteristics of the
internal reference in both 1.0 V and 0.5 V modes.
When the SENSE pin is tied to AVDD, the internal reference
is disabled, allowing the use of an external reference. An internal
reference buffer loads the external reference with an equivalent
6 kΩ load (see Figure 18). The internal buffer generates the
positive and negative full-scale references for the ADC core.
Therefore, the external reference must be limited to a maximum
of 1.0 V.
–0.25
–0.50
–0.75
–1.00
–1.25
–0.5
–1.0
–1.5
–2.0
–2.5
2.5
2.0
1.5
1.0
0.5
0
0
–40
0
–20
Figure 54. VREF Accuracy vs. Load
Figure 55. Typical VREF Drift
0.5
0
LOAD CURRENT (mA)
TEMPERATURE (°C)
VREF = 1.0V
20
1.0
40
VREF = 0.5V
1.5
60
80
2
.0
Rev. 0 | Page 27 of 80
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD6653 sample clock inputs,
CLK+ and CLK−, should be clocked with a differential signal.
The signal is typically ac-coupled into the CLK+ and CLK− pins
via a transformer or capacitors. These pins are biased internally
(see Figure 56) and require no external bias.
Clock Input Options
The AD6653 has a very flexible clock input structure. Clock input
can be a CMOS, LVDS, LVPECL, or sine wave signal. Regardless
of the type of signal being used, the clock source jitter is of the
most concern, as described in the Jitter Considerations section.
Figure 57 and Figure 58 show two preferred methods for clocking
the AD6653 (at clock rates up to 625 MHz). A low jitter clock
source is converted from a single-ended signal to a differential
signal, using an RF transformer. The back-to-back Schottky diodes
across the transformer secondary limit clock excursions into the
AD6653 to approximately 0.8 V p-p differential. This helps prevent
the large voltage swings of the clock from feeding through to other
portions of the AD6653 while preserving the fast rise and fall
times of the signal, which are critical to low jitter performance.
CLOCK
INPUT
CLOCK
INPUT
Figure 57. Transformer-Coupled Differential Clock (Up to 200 MHz)
Figure 58. Balun-Coupled Differential Clock (Up to 625 MHz)
CLK+
50Ω
0.1µF
50Ω
1nF
Figure 56. Equivalent Clock Input Circuit
1nF
2pF
100Ω
ADT1–1WT, 1:1Z
Mini-Circuits
XFMR
0.1µF
AVDD
1.2V
®
0.1µF
0.1µF
0.1µF
0.1µF
SCHOTTKY
SCHOTTKY
HSMS2822
HSMS2822
DIODES:
DIODES:
2pF
CLK+
CLK–
CLK–
AD6653
CLK+
CLK–
AD6653
ADC
AD6653
ADC