MAX512CPD Maxim Integrated Products, MAX512CPD Datasheet - Page 12
![IC DAC TRPL VOLT-OUT 8BIT 14-DIP](/photos/6/57/65726/175-14-dip_sml.jpg)
MAX512CPD
Manufacturer Part Number
MAX512CPD
Description
IC DAC TRPL VOLT-OUT 8BIT 14-DIP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX512CPD.pdf
(16 pages)
Specifications of MAX512CPD
Settling Time
70µs
Number Of Bits
8
Data Interface
Serial
Number Of Converters
3
Voltage Supply Source
Dual ±
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
14-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power Dissipation (max)
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX512CPD
Manufacturer:
MAXIM/美信
Quantity:
20 000
The MAX512 is fully specified to operate with
V
specified for single-supply operation with V
2.7V to 3.6V, covering all commonly used supply voltages
in 3V systems. The MAX512/MAX513 can also be used
with a negative supply ranging from -1.5V to -5.5V. Using a
negative supply typically improves zero-code error and
settling time (as shown in the Typical Operating
Characteristics graphs).
The two separate reference inputs for the DAC pair A/B
and the unbuffered output C allow different full-scale out-
put voltages and, if a negative supply is used, also allow
different polarity. In dual-supply mode, REFAB can vary
from V
specified range for REFAB is 0V to V
from GND to V
Power-supply sequencing is not critical. If a negative sup-
ply is used, make sure V
ground. Do not apply signals to the digital inputs until the
device is powered-up. If this is not possible, add current-
limiting resistors to the digital inputs.
Low-Cost, Triple, 8-Bit Voltage-Output DACs
with Serial Interface
_____________
Figure 3. MAX512/MAX513 Detailed Serial-Interface Timing Diagram
12
DD
= 5V ±10% and V
______________________________________________________________________________________
SCLK
LOUT
SS
DIN
CS
to (V
DD
DD
Applications Information
. Do not force REFC below ground.
Power-Supply and Reference
- 1.5V). In single-supply mode, the
SS
SS
t
CSS
t
= GND = 0V. The MAX513 is
DS
is never more than 0.3V above
t
DH
t
Operating Ranges
CH
DD
. REFC can range
DD
t
CL
ranging from
In single-supply operation (V
should be connected to the highest quality ground
available. Bypass V
to GND. For dual-supply operation, bypass V
0.1µF to 0.22µF capacitor to GND. Reference inputs
can be used without bypassing. For optimum line/load-
transient response and noise performance, bypass the
reference inputs with 0.1µF to 4.7µF to GND. Careful
PC board layout minimizes crosstalk among DAC out-
puts, reference inputs, and digital inputs. Separate ana-
log lines with ground traces between them. Make sure
that high-frequency digital lines are not routed in paral-
lel to analog lines.
With unipolar output, the output voltage and the refer-
ence voltage are the same polarity. The MAX512/
MAX513 can be used with a single supply if the refer-
ence voltages are positive. With a negative supply,
the REFAB voltage can vary from V
approximately (V
tiplication.
t
CSH
DD
Power-Supply Bypassing and
DD
- 1.5V), allowing two-quadrant mul-
t
OD
with a 0.1µF to 0.22µF capacitor
t
CSPWH
Ground Management
SS
= GND), GND and V
Unipolar Output
SS
SS
with a
SS
to