DEBB33A222KA2B Murata Electronics, DEBB33A222KA2B Datasheet - Page 69
![no-image](/images/manufacturer_photos/0/4/465/murata_electronics_sml.jpg)
DEBB33A222KA2B
Manufacturer Part Number
DEBB33A222KA2B
Description
Cap Ceramic 0.0022uF 1000VDC B 10% 9 X 4mm RDL 5mm Bulk
Manufacturer
Murata Electronics
Type
Radialr
Datasheet
1.DEBB33A681KA2B.pdf
(72 pages)
Specifications of DEBB33A222KA2B
Package/case
9(Max) X 4(Max)
Lead Pitch For Radial
5 mm
Capacitance Value
0.0022 uF
Dielectric
B
Tolerance
10 %
Voltage
1000 Vdc
Product Depth
4(Max) mm
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DEBB33A222KA2B
Manufacturer:
MURATA
Quantity:
1 750
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Operating and Storage Environment
1. Vibration and Impact
2. Soldering
3. Bonding, Resin Molding and Coating
Vibration and Impact
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
The insulating coating of capacitors does not form a
perfect seal; therefore, do not use or store
capacitors in a corrosive atmosphere, especially
where chloride gas, sulfide gas, acid, alkali, salt
or the like are present. And avoid exposure to
moisture. Before cleaning, bonding or molding this
product, verify that these processes do not affect
product quality by testing the performance of a
cleaned, bonded or molded product in the intended
Do not expose a capacitor or its leads to excessive
shock or vibration during use.
Do not expose a capacitor or its leads to
excessive shock or vibration during use.
When soldering this product to a PCB/PWB, do not
exceed the solder heat resistance specification of
the capacitor. Subjecting this product to excessive
heating could melt the internal junction solder and
may result in thermal shocks that can crack the
ceramic element.
When soldering capacitor with a soldering iron, it
should be performed in following conditions.
Before bonding, molding or coating this product,
!Caution (Storage and Operating Condition)
!Caution (Soldering and Mounting)
verify that these processes do not affect the
quality of capacitor by testing the performance
!Caution (Handling)
Temperature of iron-tip: 400 degrees C. max.
Soldering iron wattage: 50W max.
Soldering time: 3.5 sec. max.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
High Voltage Ceramic Capacitors !Caution
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY
RESULT, WORST CASE, IN A SHORT CIRCUIT
AND CAUSE FUMING OR PARTIAL DISPERSION
WHEN THE PRODUCT IS USED.
equipment. Store the capacitors where the
temperature and relative humidity do not exceed -10
to 40 degrees centigrade and 15 to 85%.
Use capacitors within 6 months after delivery.
of the bonded, molded or coated product in the
intended equipment.
In case the amount of applications,
dryness/hardening conditions of adhesives and
molding resins containing organic solvents
(ethyl acetate, methyl ethyl ketone, toluene, etc.)
are unsuitable, the outer coating resin of a
capacitor is damaged by the organic solvents and
it may result, worst case, in a short circuit.
The variation in thickness of adhesive, molding
resin or coating may cause outer coating resin
cracking and/or ceramic element cracking of a
capacitor in a temperature cycling.
C85E.pdf
67
08.10.29
11