ATF1500A-10JI Atmel, ATF1500A-10JI Datasheet
ATF1500A-10JI
Specifications of ATF1500A-10JI
Available stocks
Related parts for ATF1500A-10JI
ATF1500A-10JI Summary of contents
Page 1
... Green (Pb/Halide-fee/RoHS Compliant) Package Options Description The ATF1500A is a high-performance, high-density complex PLD. Built on an advanced Flash technology, it has maximum pin-to-pin delays of 7.5 ns and supports sequential logic operation at speeds up to 125 MHz. With 32 logic macrocells and inputs, it easily integrates logic from several TTL, SSI, MSI and classic PLDs. ...
Page 2
... Note: 1. Arrows connecting macrocells indicate direction and groupings of CASIN/CASOUT data flow. The ATF1500A has 32 bi-directional I/O pins and four dedi- cated input pins. Each dedicated input pin can also serve as a global control signal: register clock, register reset or output enable. Each of these control signals can be selected for use individually within each macrocell ...
Page 3
... Bus-friendly Pin-keeper Input and I/O’s All Input and I/O pins on the ATF1500A have programma- ble “pin-keeper” circuits. If activated, when any pin is driven high or low and then subsequently left floating, it will stay at that previous high or low level ...
Page 4
... Morgan minimization of the product terms. The XOR gate is also used to emulate T-type flip-flops. Flip-flop The ATF1500A’s flip-flop has very flexible data and control functions. The data input can come from either the XOR gate or from a separate product term. Selecting the sepa- rate product term allows creation of a buried registered feedback within a combinatorial output macrocell ...
Page 5
... The asynchronous preset (AP) can be a product term or always off. Output Select and Enable The ATF1500A macrocell output can be selected as regis- tered or combinatorial. When the output is registered, the same registered signal is fed back internally to the global bus. When the output is combinatorial, the buried feedback ...
Page 6
... CC ATF1500A(L) 6 *NOTICE: (1) (1) Note: 1. (1) Condition (Max Min Com. ATF1500A Ind Max Com ATF1500AL Ind Max 0.5V OUT V , Min < < Max Min Min -0 Stresses beyond those listed under “Absolute Maximum Ratings” ...
Page 7
AC Waveforms Register AC Characteristics, Input Pin Clock Symbol Parameter Min (1) t Clock to Output COS t Clock to Feedback CFS t I, I/O Setup Time SIS Feedback Setup t SFS Time Input, I/O, Feedback t HS Hold Time ...
Page 8
... WA External Feedback 1/( SIA COA f Internal Feedback MAXA 1/( SFA CFA No Feedback 1/( Reset Pin Recovery t 0 RPRA Time Reset Term t 4 RTRA Recovery Time Note: 1. For slow slew outputs, add t ATF1500A( -10 -12 Max Min Max Min Max 7 95.2 76.9 62.5 125 100 90 ...
Page 9
AC Characteristics Symbol Parameter I, I (1) t Non-Registered PD Output t I, I/O to Feedback PD2 Feedback to (1) t Non-Registered PD3 Output Feedback to t PD4 Feedback OE Term to Output ( Enable ...
Page 10
... Pin or Product Term. Input Test Waveforms and Measurement Levels 3.0V AC DRIVING 1.5V LEVELS 0.0V ≤ 1 Pin Capacitance ( MHz 25° OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. ATF1500A( -10 -12 Min Max Min Max Min Max ...
Page 11
... Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF1500A fuse patterns. Once programmed, fuse verify and preload are prohibited. However, the 160-bit User Signature remains accessible. The security fuse should be programmed last, as its effect is immediate ...
Page 12
... NORMALIZED SUPPLY CURRENT vs. INPUT FREQUENCY ATF1500A ( 25˚ NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE ATF1500 (TA = 25˚ OUTPUT SOURCE CURRENT vs. SUPPLY VOLTAGE ( OUTPUT SOURCE CURRENT vs. OUTPUT VOLTAGE ( ATF1500A( 2.4V 25˚ 2.4V 25˚ SUPPLY CURRENT vs. FREQUENCY ATF1500AL ( 25˚ NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE ...
Page 13
OUTPUT SINK CURRENT vs. OUTPUT VOLTAGE ( 25˚ INPUT CLAMP CURRENT vs. INPUT VOLTAGE INPUT CURRENT vs. INPUT VOLTAGE ( 25˚C) CC NORMALIZED t COS vs. SUPPLY VOLTAGE ...
Page 14
... NORMALIZED t vs. SUPPLY VOLTAGE (TA = 25˚C) t SIS NORMALIZED t vs. SUPPLY VOLTAGE (TA = 25˚C) t SIA ATF1500A(L) 14 SIS t SIS SIA t SIA NORMALIZED t SIS vs. AMBIENT TEMPERATURE (V = 5V) CC NORMALIZED t SIA vs. AMBIENT TEMPERATURE (V = 5V) CC ...
Page 15
... Thin Plastic Gull Wing Quad Flatpack (TQFP) 44J 44-lead, Plastic J-leaded Chip Carrier (PLCC) Ordering Code ATF1500A-7AC ATF1500A-7JC ATF1500A-10AC ATF1500A-10JC ATF1500A-10AI ATF1500A-10JI ATF1500A-12AC ATF1500A-12JC ATF1500A-12AI ATF1500A-12JI ATF1500A-15AC ATF1500A-15JC ATF1500A-15AI ATF1500A-15JI ATF1500AL-20AC ATF1500AL-20JC ATF1500AL-20AI ATF1500AL-20JI Ordering Code ATF1500A-10AU ATF1500A-10JU ...
Page 16
... This package conforms to JEDEC reference MS-026, Variation ACB. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R ATF1500A( TITLE 44A, 44-lead Body Size, 1 ...
Page 17
PLCC 1.14(0.045) X 45˚ 0.51(0.020)MAX 45˚ MAX (3X) Notes: 1. This package conforms to JEDEC reference MS-018, Variation AC. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. ...
Page 18
... Revision History ATF1500A(L) 18 Revision Comments Green package options added. 0759F ...
Page 19
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...