PVZ3A502A01R00 Murata, PVZ3A502A01R00 Datasheet - Page 73

• Manufacturer Part Number: PVZ3A502A01R00
• Description: Trimmer Resistors - SMD 5K OHM SMD 3MM
• Manufacturer: Murata
• Series: PVZ3Ar

Specifications of PVZ3A502A01R00

• Resistance: 5 KOhms
• Tolerance: 30 %
• Power Rating: 0.1 Watt (1/10 Watt)
• Operating Temperature Range: - 25 C to + 85 C
• Element Type: Carbon
• Number Of Turns: 1
• Product: Single-Turn Trimmer Potentiometers
• Taper: Linear
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

9
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Soldering profile for Lead-free solder (96.5Sn/3.0Ag/0.5Cu)
Uncontrolled mechanical force except usual rotation on
the hollow rotor of product, may cause big change of
electrical characteristic, big increase of rotational
torque or mechanical damage of product.
Therefore, please pay your attention on the following
points for your design.
1. Please make sure the connecting impedance is not to
2. To minimize the processing error and noise
72
150 to 180 60 to 120
150 to 180 60 to 120
Temp. (T1)
Temp. (T1)
SV01 Series Notice
Temperature of Soldering Iron Tip
Soldering Profile
Notice (Handling)
Notice (Other)
be less than 10M ohm. The rotary position sensor
is designed to connect the output terminal and A/D
port of the microprocessor directly. Therefore,
connecting impedance presupposes certain M ohm and
the contact resistance is set high.
influence which occur in rare cases, when data is
installed through the product, please note the
following items and program your software.
Reflow Soldering Profile
Soldering Iron
C
C
Pre-heating
Pre-heating
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
T1
Time (t1)
Time (t1)
sec.
sec.
350 10
C
Temp. (T2)
Temp. (T4)
t1
220
230
T3
T2
C
C
Standard Profile
Heating
Heating
Limit Profile
t2
t3
Time (t2)
Time (t3)
30 to 60
30 to 50
sec.
sec.
Time (s)
T5
T4
Limit Profile
Standard Profile
Temperature
Temperature
260 +5/-0
245 3
Soldering Time
Peak
Peak
(T3)
(T5)
C
C
3 max.
sec.
of Reflow
of Reflow
Cycle
Cycle
Time
Time
2
2
Standard Condition
1. The fixing method of product must be soldering by
2. Your connecting shaft must be sustained by your
3. Before using rotary position sensor, please test
4. MURATA cannot guarantee rotary position sensor
(1) Data install should be done plural times and
(2) Data considered as error should be invalid.
(3) If suspicious data is found, the data should be
2. Soldering profile for Eutectic solder (63Sn/37Pb)
the terminals of product. And please don't fix by
screw cramping of supporting board which might
cause mechanical deformation of product.
bearing and any uncontrolled force should not
apply on the hollow rotor of product.
after assembly in your particular mass production
system.
integrity when used under conditions other than
those specified in this document.
Temp. (T1)
Soldering Iron Power Output
applied the mean value.
re-installed.
(Limit profile: refer to 1)
150
C
Pre-heating
T1
30 max.
60 to 120
Time (t1)
W
sec.
Temp. (T2)
t1
183
T3
T2
C
Standard Profile
Heating
t2
Time (t2)
sec.
30
Time (s)
Cycle of Soldering Iron
Standard Profile
Temperature
Peak
230
(T3)
Time
C
1
of Reflow
Cycle
Time
1
R50E.pdf
05.9.9