EP1K10TC144-2N Altera, EP1K10TC144-2N Datasheet - Page 40
![IC ACEX 1K FPGA 10K 144-TQFP](/photos/6/70/67061/544-144-tqfp_sml.jpg)
EP1K10TC144-2N
Manufacturer Part Number
EP1K10TC144-2N
Description
IC ACEX 1K FPGA 10K 144-TQFP
Manufacturer
Altera
Series
ACEX-1K®r
Datasheet
1.EP1K10TC100-3N.pdf
(86 pages)
Specifications of EP1K10TC144-2N
Number Of Logic Elements/cells
576
Number Of Labs/clbs
72
Total Ram Bits
12288
Number Of I /o
92
Number Of Gates
56000
Voltage - Supply
2.375 V ~ 2.625 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
144-TQFP, 144-VQFP
Family Name
ACEX™ 1K
Number Of Usable Gates
10000
Number Of Logic Blocks/elements
576
# I/os (max)
92
Frequency (max)
200MHz
Process Technology
CMOS
Operating Supply Voltage (typ)
2.5V
Logic Cells
576
Ram Bits
12288
Device System Gates
56000
Operating Supply Voltage (min)
2.375V
Operating Supply Voltage (max)
2.625V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
144
Package Type
TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
544-1829
EP1K10TC144-2N
EP1K10TC144-2N
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP1K10TC144-2N
Manufacturer:
ALTERA
Quantity:
14
ACEX 1K Programmable Logic Device Family Data Sheet
40
PCI Pull-Up Clamping Diode Option
ACEX 1K devices have a pull-up clamping diode on every I/O, dedicated
input, and dedicated clock pin. PCI clamping diodes clamp the signal to
the V
diodes can also be used to limit overshoot in other systems.
Clamping diodes are controlled on a pin-by-pin basis. When V
3.3 V, a pin that has the clamping diode option turned on can be driven by
a 2.5-V or 3.3-V signal, but not a 5.0-V signal. When V
that has the clamping diode option turned on can be driven by a 2.5-V
signal, but not a 3.3-V or 5.0-V signal. Additionally, a clamping diode can
be activated for a subset of pins, which allows a device to bridge between
a 3.3-V PCI bus and a 5.0-V device.
Slew-Rate Control
The output buffer in each IOE has an adjustable output slew rate that can
be configured for low-noise or high-speed performance. A slower slew
rate reduces system noise and adds a maximum delay of 4.3 ns. The fast
slew rate should be used for speed-critical outputs in systems that are
adequately protected against noise. Designers can specify the slew rate
pin-by-pin or assign a default slew rate to all pins on a device-wide basis.
The slow slew rate setting affects only the falling edge of the output.
Open-Drain Output Option
ACEX 1K devices provide an optional open-drain output (electrically
equivalent to open-collector output) for each I/O pin. This open-drain
output enables the device to provide system-level control signals (e.g.,
interrupt and write enable signals) that can be asserted by any of several
devices. It can also provide an additional wired-OR plane.
MultiVolt I/O Interface
The ACEX 1K device architecture supports the MultiVolt I/O interface
feature, which allows ACEX 1K devices in all packages to interface with
systems of differing supply voltages. These devices have one set of V
pins for internal operation and input buffers (VCCINT), and another set for
I/O output drivers (VCCIO).
CCIO
value and are required for 3.3-V PCI compliance. Clamping
CCIO
Altera Corporation
is 2.5 V, a pin
CCIO
is
CC