EP2AGX45DF29I5 Altera, EP2AGX45DF29I5 Datasheet - Page 41
![no-image](/images/manufacturer_photos/0/0/40/altera_sml.jpg)
EP2AGX45DF29I5
Manufacturer Part Number
EP2AGX45DF29I5
Description
IC ARRIA II GX FPGA 45K 780FBGA
Manufacturer
Altera
Series
Arria II GXr
Datasheets
1.EP2AGX45CU17C6N.pdf
(96 pages)
2.EP2AGX45CU17C6N.pdf
(14 pages)
3.EP2AGX45CU17C6N.pdf
(692 pages)
4.EP2AGX45CU17C6N.pdf
(10 pages)
5.EP2AGX45CU17C6N.pdf
(88 pages)
Specifications of EP2AGX45DF29I5
Number Of Logic Elements/cells
42959
Number Of Labs/clbs
1805
Total Ram Bits
3435
Number Of I /o
364
Voltage - Supply
0.87 V ~ 0.93 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
780-FBGA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP2AGX45DF29I5N
Manufacturer:
ALTERA
Quantity:
201
Company:
Part Number:
EP2AGX45DF29I5N
Manufacturer:
ALTERA
Quantity:
853
Chapter 1: Device Datasheet for Arria II Devices
Switching Characteristics
Table 1–35. Transceiver Specifications for Arria II GZ Devices (Part 6 of 6)
December 2010 Altera Corporation
Digital reset pulse width
Notes to
(1) The 3× speed grade is the fastest speed grade offered in the following Arria II GZ devices: EP2AGZ225, EP2AGZ300, and EP2AGZ350.
(2) The minimum reconfig_clk frequency is 2.5 MHz if the transceiver channel is configured in Transmitter only mode. The minimum
(3) The device cannot tolerate prolonged operation at this absolute maximum.
(4) You must use the 1.1-V RX V
(5) The rate matcher supports only up to
(6) Time taken to rx_pll_locked goes high from rx_analogreset de-assertion. Refer to
(7) Time for which the CDR must be kept in lock-to-reference mode after rx_pll_locked goes high and before rx_locktodata is asserted in
(8) Time taken to recover valid data after the rx_locktodata signal is asserted in manual mode. Refer to
(9) Time taken to recover valid data after the rx_freqlocked signal goes high in automatic mode. Refer to
(10) A GPLL may be required to meet the PMA-FPGA fabric interface timing above certain data rates. For more information, refer to the
(11) The Quartus II software automatically selects the appropriate slew rate depending on the configured data rate or functional mode.
(12) The Quartus II software automatically selects the appropriate /L divider depending on the configured data.
(13) If your design uses more than one dynamic reconfiguration controller (altgx_reconfig) instances to control the transceiver (altgx)
(14) The differential eye opening specification at the receiver input pins assumes that Receiver Equalization is disabled. If you enable Receiver
(15) The rise and fall time transition is specified from 20% to 80%.
reconfig_clk frequency is 37.5 MHz if the transceiver channel is configured in Receiver only or Receiver and Transmitter mode.
manual mode. Refer to
Clocking for Arria II Devices
channels physically located on the same side of the device AND if you use different reconfig_clk sources for these altgx_reconfig
instances, the delta time between any two of these reconfig_clk sources becoming stable must not exceed the maximum specification listed.
Equalization, the receiver circuitry can tolerate a lower minimum eye opening, depending on the equalization level. Use H-Spice simulation to
derive the minimum eye opening requirement with Receiver Equalization enabled.
Description
Table
Symbol/
1–34:
Figure 1–1 on page
chapter.
ICM
setting if the input serial data standard is LVDS.
Conditions
±
300 ppm.
—
1–34.
Min
–C3 and –I3
Typ
Minimum is two parallel clock cycles
Arria II Device Handbook Volume 3: Device Datasheet and Addendum
(1)
Max
Figure 1–1 on page
Min
Figure 1–1 on page
Figure 1–2 on page
–C4 and –I4
1–34.
Typ
Max
1–34.
1–34.
Transceiver
Unit
—
1–33